Aspire 9410 / 7110 TravelMate 5610 / 5110 Service Guide · Aspire 9410 / 7110 TravelMate 5610 / 5110 Service Guide ... (Aspire 9410 / 7110 series) T Acer ClearVisionTM ... 7 N/A Touchpad - [PDF Document] (2024)

Acer

Aspire 9410 / 7110TravelMate 5610 / 5110

Service Guide

Service guide files and updates are available on the ACER/CSD web. For more information, please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

II

Revision HistoryPlease refer to the table below for the updates of Aspire 9410 / 7110 and TravelMate 5610 / 5110 service guide.

Date Chapter Updates

III

CopyrightCopyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

IV

DisclaimerThe information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed “as is”. Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Incorporated.Intel is a registered trademark of Intel Corporation.Pentium and Pentium D are trademarks of Intel Corporation.Other brand and product names are trademarks and/or registered trademarks of their respective holders.

V

ConventionsThe following conventions are used in this manual:

SCREEN MESSAGES Denotes actual messages that appear on screen.

NOTE Gives bits and pieces of additional information related to the current topic.

WARNING Alerts you to any damage that might result from doing or not doing specific actions.

CAUTION Gives precautionary measures to avoid possible hardware or software problems.

IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.

VI

PrefaceBefore using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's “global” product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

VII

Table of Contents

Chapter 1 System Specification 1Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Display and Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Storage Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Power Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . 3Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Outlook Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Base View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Lock keys and Embedded Numeric Keypad . . . . . . . . . 10Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Easy-launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Touch pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Touch pad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . 18

Acer eDataSecurity Management . . . . . . . . . . . . . . . . . 19Acer eLock Management . . . . . . . . . . . . . . . . . . . . . . . 21Acer ePerformance Management . . . . . . . . . . . . . . . . . 22Acer eRecovery Management . . . . . . . . . . . . . . . . . . . 23Acer eSettings Management . . . . . . . . . . . . . . . . . . . . . 24Acer eNet Management . . . . . . . . . . . . . . . . . . . . . . . . 25Acer ePower Management . . . . . . . . . . . . . . . . . . . . . . 27Acer ePresentation Management . . . . . . . . . . . . . . . . . 29

Acer OrbiCam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Acer GridVista (dual-display compatible) . . . . . . . . . . . 36Launch Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Norton AntiVirus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38How do I check for viruses? . . . . . . . . . . . . . . . . . . . . . 38

Hardware Specification and Configuration . . . . . . . . . . . . . . 39BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Invoking BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

VIII

Chapter 2 System Utilities 48Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Chapter 3 Machine Disassembly and Replacement 56General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . 58Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . 60Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . 60Removing the MiniPCI Card and the Memory . . . . . . . 61Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . 62Separating the LCD Module and Main Unit . . . . . . . . . 63Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . 64LCD Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Chapter 4 Troubleshooting 75System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 76

External Diskette Drive Check . . . . . . . . . . . . . . . . . . . 76External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . 76Keyboard or Auxiliary Input Device Check . . . . . . . . . . 76Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . 77Check the Power Adaptor . . . . . . . . . . . . . . . . . . . . . . . 77Check the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . 78Touch pad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Power-On Self-Test (POST) Error Message . . . . . . . . . . . . 80Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Error Message List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . 82Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . 87Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Chapter 5 Jumper and Connector Location 93Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Chapter 6 FRU (Field Replaceable Unit) List 96Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

IX

System Specification

Chapter 1

Features

Platform

Aspire 9410 / TravelMate 5610 Series

Intel® CoreTM Duo processor T2300/T2400/T2500/T2600 (2MB L2 cache, 1.66/1.83/2/2.16GHz, 667MHz FSB)

Mobile Intel® 945GM/PM Express chipsetDDR2 533/667 memory

Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology

Aspire 7110 / TravelMate 5110 Series

Intel® Celeron® M processor 410/420/430 (1MB L2 cache, 1.46/1.60/1.73GHz, 533MHz FSB)

Mobile Intel® 940GML Express chipset

Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology

System Memory

Aspire 9410 / TravelMate 5610 Series

Up to 2GB of DDR2 533/667MHz memory, upgradeable to 4GB using two soDIMM modules (dual-channel support)

Aspire 7110 / TravelMate 5110 Series

Up to 1GB of DDR2 533MHz memory, upgradeable to 2GB using two soDIMM modules (dual-channel support)

Display and Graphics

17.1” WXGA + 200-nit Acer CrystalBriteTM colour TFT LCD (Aspire 9410 / 7110 series) or high brightness TFT LCD (TravelMate 5610 / 5110 series), 1440 x 900 pixel resolution, supporting simultaneous multi-window viewing via Acer GridVistaTM

NVIDIA® GeForce® Go 7300 up to 512MB TurboCacheTM (256MB of dedicated GDDR2 VRAM, 256MB of shared system memory), supporting Microsoft DirectX 9.0, Shader Model3.0, OpenEXR High Dynamic Range (HDR) technology, NVIDIA PowerMizer

Mobile Intel® 945GM/940GML Express chipset (Aspire 9410 / 7110 series) or 945GM Express chipset (TravelMate 5610 / 5110 series) with integrated 3D graphics, featuring Intel® Graphics Media Accelerator (GMA) 950, up to 224MB of shared system memory, supporting Microsoft® DirectX® 9.0 and PCI Express® and dual independent displays

16.7 million colours

Chapter 1 1

MPEG-2/DVD hardware-assisted capability

Acer CinemaVisionTM technology (Aspire 9410 / 7110 series)

Acer ClearVisionTM technology (Aspire 9410 / 7110 series)NOTE: TurboCacheTM memory allocation varies depending on configuration.

Storage Subsystem

60/80/100/120GB or higher hard disk drive (Aspire 9410 / 7110 series)

80/100/120GB or higher hard disk drive with Acer Disk Anti-Shock Protection, DASP (TravelMate 5610 / 5110 series)

Optical drive options:DVD-Super Multi double-layer

DVD-Dual double-layer

DVD/CD-RW combo drive

5-in-1 card reader, supporting Secure Digital (SD), MultiMediaCard (MMC), Memory Stick® (MS), Memory Stick PROTM (MS PRO), xD-Picture CardTM (xD)

Communication

Acer Video Conference featuring Voice and Video over internet Protocol (VVoIP) support via Acer OrbiCamTM and optional Acer Bluetooth® VoIP phone

Acer OrbiCamTM integrated 1.3 megapixel or 310,000 pixel CMOS camera (for selected models), featuring:

225 degree ergonomic rotation

Acer VisageONTM technology (for 1.3 megapixel camera models only)

Acer PrimaLiteTM technology

Modem: 56K ITU V.92 with PTT approval; Wake-on-Ring ready

LAN: gigabit Ethernet; Wake-on-LAN ready

WPAN: Bluetooth® 2.0 + EDR (Enhanced Data Rate)

WLAN: Intel® PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology (Aspire 9410 / TravelMate 5610 series); Integrated Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology (Aspire 7110 / TravelMate 5110 series)

I/O Interface

PC Card slot (one Type II)

Four USB 2.0 ports

External display (VGA) port

Headphones/speaker/line-out jack with S/PDIF support

Microphone-in jack

Line-in jack

2 Chapter 1

Ethernet (RJ-45) port

Modem (RJ-11) port

DC-in jack for AC adapter

Power Subsystem

ACPI 2.0 CPU power management standards: Stand-by and Hibernation power-saving modes support

71W 4800mAh (8-cell) or 44W 4000mAh (6-cell) Li-Ion battery pack

Acer QuicChargeTM technology: 80% charge in 1 hour; 2-hour rapid charge system-off; 2.5-hour charge-in-use

3-pin 90W AC adapter

Dimensions and Weight

With Acer OrbiCamTM

400 (W) x 295 (D) x 31.4/39.9 (H) mm (15.75 x 11.61 x 1.24/1.57 inches)

3.81 kg (8.39 lbs.) with 8-cell battery pack

3.68 kg (8.10 lbs.) with 6-cell battery pack

Without Acer OrbiCamTM

400 (W) x 295 (D) x 31.4/39.9 (H) mm (15.75 x 11.61 x 1.24/1.57 inches)

3.79 kg (8.35 lbs.) with 8-cell battery pack

3.66 kg (8.06 lbs.) with 6-cell battery pack

Environment

Temperature

Operating: 5 oC to 35 oC

Non-operating: -20 oC to 65 oC

Humidity (non-condensing)Operating: 20% to 80%

Non-operating: 20% to 80%

Chapter 1 3

Block Diagram

4 Chapter 1

# Icon

.

# Item Description

Outlook Tour

Front View

Left: Aspire 9410 / 7110 Series Right: TravelMate 5610 / 5110 Series

# Icon Item Description1 N/A Built-in camera 1.3 megapixel or 310,000 pixel web camera for video

communication (for selected models)

2 N/A Display screen Also called Liquid-Crystal Display (LCD), displays computer output.

3 N/A Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computer’s functions and components.

4 Wireless communication button

Enable/disables Wireless function. Indicates the status of wireless LAN communications.

5 Bluetooth communication button

Enable/disables Bluetooth function. Indicates the status of Bluetooth communications.

6 N/A Microphone Internal microphone for sound recording

7 N/A Touchpad Touch-sensitive pointing device which functions like a computer mouse

8 N/A Click buttons (left, center and right)

The left and right buttons function like the left and right mouse buttons; the center button serves as a four-way scroll button.

Just for Starters...

Item Description

Just for Starters..

# Icon Item Description

"Launch keys" on page 10

# Icon Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

Chapter 1 5

# Icon

# Icon Item Description

on

# Icon Item Description

"Launch keys" on page 10

# Item Description

# Item Description

Closed Front View

Left: Aspire 9410 / 7110 Series Right: TravelMate 5610 / 5110 Series

9 N/A Palmrest Comfortable support area for your hands when you use the computer.

10 N/A Keyboard Serves for entering data into your computer.

11 N/A Power button Turns the computer on and off.

12 N/A Easy-launch buttons Buttons for launching frequently used programs.

# Icon Item Description1 N/A Speakers Left and right speakers deliver stereo audio output.

2 Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).

3 Microphone-in jack Accepts input from external microphones.

4 Headphones/speaker/line-out jack with S/PDIF support

Connects to audio line-out devices (e.g., speakers, headphones).

5 Power indicator Indicates the computer’s power status.

6 Battery indicator Indicates the computer’s battery status.

7 Bluetooth communication indicator

Indicates the status of Bluetooth communication.

8 Wireless communication indicator

Indicates the status of wireless LAN communication.

9 N/A Latch Locks and releases the lid.

"Easy-launch buttons" on

page 27

Item Description

"Easy-launch buttons"

page 27

# Icon Item Description# Icon Item Description

# Icon Item Description

Note:

# Icon Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

6 Chapter 1

# Icon Item Description

# Ico

# Icon Item Description

# Icon Item Description

# Icon Item Description

# Icon

Left View

Left: Aspire 9410 / 7110 Series Right: TravelMate 5610 / 5110 Series

Right View

Left: Aspire 9410 / 7110 Series Right: TravelMate 5610 / 5110 Series

# Icon Item Description1 Kensington lock slot Connects to a Kensington-compatible computers security lock.

2 N/A Optical disk drive Internal optical drive; accepts CDs or DVDs (slot-load or tray-load depending on model).

3 N/A Optical disk access indicator

Lights up when the optical disk drive is active.

4 N/A Optical disk drive eject button

Ejects the drive tray from the drive (location depends on model).

5 N/A Emergency eject hole Ejects the drive tray when the computer is turned off.

# Icon Item Description1 N/A PC Card slot eject button Ejects the PC Card from the slot.

2 PC Card slot Accepts one Type II PC Card.

3 5-in-1 card reader Accepts Memory Stick (MS), Memory Stick Pro (MS PRO), MultiMediaCard (MMC), Secure Digital (SD) and xD-Picture Card (xD).

4 Three USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB camera).

5 N/A Ventilation slots Enable the computer to stay cool, even after prolonged use.

n Item Description # Icon Item Description

# Icon Item Description

Note:

Item Description

# Icon Item Description

# Icon Item Description

Note:

# Icon Item Description

"Easy-launch buttons" on page 10

# Icon Item Description

# Item Description

# Icon Item Description

Chapter 1 7

# Icon Item Description

Note:

# Icon Item Description

Note:

# Icon Item Description

# Icon Item Description

# Icon

# Icon Item Description

Note:

# Icon Item Description

# Icon Item Description

Rear View

Left: Aspire 9410 / 7110 Series Right: TravelMate 5610 / 5110 Series

6 DC-in jack Connects to an AC adapter.

# Icon Item Description1 USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB camera).

2 External display (VGA) port Connects to an external display device (e.g., external monitor, LCD projector).

3 Modem (RJ-11) port Connects to a phone line.

4 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000-based networks.

5 N/A Battery Powers the computer.

Item Description

# Icon Item Description

# Icon Item Description

# Icon Item Description# Icon Item Description

Note:

# Icon Item Description

Note:

# Icon Item Description

# Icon Item Description

8 Chapter 1

Note:

Base View

Upper: Aspire 9410 / 7110 SeriesLower: TravelMate 5610 / 5110 Series

# Icon Item Description1 N/A Battery release latch Releases the battery for removal.

2 N/A Cooling fan Helps keep the computer cool.NOTE: Do not cover or obstruct the opening of the fan.

3 N/A Mini PCI card bay Houses the computer’s Mini PCI card.

4 N/A Ventilation slots Enable the computer to stay cool, even after prolonged use.

5 N/A Memory compartment Houses the computer’s main memory.

6 N/A PCI Express Mini Card bay Houses the computer’s PCI Express Mini card.

7 N/A Hard disk bay Houses the computer’s hard disk (secured with screws).

8 N/A Battery lock Locks the battery in position.

9 N/A Battery bay Houses the computer’s battery pack.

8 N/A Acer DASP (Disk Anti-Shock Protection)

Protects the hard disk drive from shocks and bumps. (TravelMate 5610 / 5110 Series)

9 N/A Battery lock Locks the battery in position.

10 N/A Battery bay Houses the computer’s battery pack.

# Item Description

Note

# Item Description

Note

Chapter 1 9

Using the Keyboard The full-sized keyboard includes an embedded numeric keypad, separate cursor, lock, Windows, function and special keys.

Lock keys and Embedded Numeric Keypad

The keyboard has three lock keys which you can toggle on and off.

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.

Lock DescriptionCaps Lock When Caps Lock is on, all alphabetic characters are typed in uppercase.

Num LockFn + F11

When Num Lock is on, the right hand side numeric keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators +, -, *, and /). When Num Lock is off, the keys assume cursor and other shortcut functions.

Scroll LockFn + F12

When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. scroll Lock does not work with some applications.

Desired access Num Lock on Num Lock offNumber keys on embedded keypad

Type numbers in a normal manner.

N/A

Cursor-control keys on embedded keypad

Hold Shift while using cursor-control keys.

Hold Fn while using cursor-control keys.

Main keyboard keys Hold Fn while typing letters on embedded keypad.

Type the letters in a normal manner.

Lock key Description

<Fn> + <F12>

Desired access Num Lock on Num Lock off

<Shift> <Fn>

<Fn>

10 Chapter 1

H

<F

<F

on

<F

<F

<F

<F

<F

<F

<F

<F

<F

<F

Windows keys

The keyboard has two keys that perform Windows-specific functions.

Hotkeys

The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

Key Icon DescriptionWindows key Press alone. This key has the same effect as clicking on the Windows

Start button. It launches the Start menu. It can also be used with other keys to provide a variety of functions:

+ Tab: Activates the next Taskbar button.

+ E: Opens the My Computer window.

+ F1: Opens Help and Support.

+ F: Opens the Find (All Files dialog box).

+ R: Opens the Run dialog box.

+ M: Minimizes all windows.

Shift + + M: Undoes the minimize all windows action.

Application key This key has the same effect as clicking the right mouse button. It opens the application’s context menu.

Hot Key Icon Function DescriptionFn + F1 Hot key help Displays help on hot keys.

Fn + F2 Acer eSetting Launches the Acer eSettings in Acer Empowering Technology.

Fn + F3 Acer ePower Management

Launches the Acer ePower Management in Acer Empowering Technology.

Fn + F4 Sleep Leads the computer to Sleep mode.

<Fn>

Key Description

< > + <Tab>:

< > + <E>:

< > + <F1>:

< > + <F>:

+ <R>:

< > + <M>:

<Shift> + < > + <M>: <Fn>

Key Description

< > + <Tab>:

< > + <E>:

< > + <F1>:

< > + <F>:

+ <R>:

< > + <M>:

<Shift> + < > + <M>:

otkey Icon Function Description

n> + <F1>

n> + <F2>

"Acer eManager"

page 20

n> + <F3>

n> + <F4>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

Chapter 1 11n> + <F5>

n> + <F6>

n> + <F7>

n> + <F8>

n> + < >

n> + < >

n> + < >

n> + < >

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<

<

<

<

<

<

<

<

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

<

<

<

<

<

<

<

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

Hotkey Icon Function Description

<Fn> + <F1>

<Fn> + <F2>

"Acer eManager" on

page 20

<Fn> + <F3>

<Fn> + <F4>

<Fn> + <F5>

Special keys

You can locate the Euro symbol and the US dollar sign on the upper-center and/or bottom-right side of the keyboard.

The Euro Symbol

1. Open a text editor or word processor.

2. Either directly press the Euro key on the bottom-right side of the keyboard, or hold Alt Gr key then press the Euro symbol on the number five key.

NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/typography/faq/faq12.htm for more information.

The US Dollar Sign

1. Open a text editor or word processor.

Fn + F5 Display toggle Switches the display output between the display screen, external monitor (if connected) and both.

Fn + F6 Screen blank Turns off the display screen backlight to save power. Press any key to return.

Fn + F7 Touchpad toggle Turns the internal touchpad on and off.

Fn + F8 Speaker toggle Turns the speakers on and off.

Fn + Volume up Increases the sound volume.

Fn + Volume down Decreases the sound volume.

Fn + Brightness up Increases the screen brightness.

Fn + Brightness down Decreases the screen brightness.

Hot Key Icon Function Description<Fn> + <F5>

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

Fn> + <F5>

Fn> + <F6>

Fn> + <F7>

Fn> + <F8>

Fn> + < >

Fn> + < >

Fn> + < >

Fn> + < >

Fn> + <F6>

Fn> + <F7>

Fn> + <F8>

Fn> + < >

Fn> + < >

Fn> + < >

Fn> + < >

<Fn> + <F5>

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F5>

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F4>

<Fn> + <F5>

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + <F6>

<Fn> + <F7>

<Fn> + <F8>

<Fn> + < >

<Fn> + < >

<Fn> + < >

<Fn> + < >

Alt Gr>

<5>

Note

www.microsoft.com/typography/faq/faq12.htm

<Shift>

<4>

12 Chapter 1Note:

2. Either directly press the $ key on the bottom-right side of the keyboard, or hold Shift and then press the US dollar sign on the number four key.

NOTE: This function varies according to the language settings.

Chapter 1 13

IndicatorsThe computer provides an array of three indicators located above the keyboard, in addition to four indicators on the front cover. These indicators show the status of the computer and its components.

The front panel indicators are visible even when the computer cover is closed up.

Icon Item DescriptionHDD Indicates when the hard disk drive is active.

Caps Lock Lights up when Caps Lock is activated.

Num Lock Lights up when Num Lock is activated.

Power Lights when the computer is on.

Battery Lights when the battery is being charged.

Bluetooth Indicates the status of Bluetooth communication

Wireless LAN Indicates the status of wireless LAN communication

Icon Function Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

"Launch keys" on page 10

# Icon Item Description

# Item Description

14 Chapter 1

1. Charging:

2. Fully charged:

Easy-launch ButtonsThere are several conveniently located easy-launch buttons. They are one user-programmable button, web browser button, mail button, and Acer Empowering Key . Press to run the Acer Empowering Technology. Although the mail and web browser buttons are pre-set to E-mail and Internet programs, they can be redefined by users. To set the web browser, mail and programmable buttons, run the Acer Launch Manager.

Easy-launch button Default applicationAcer Empowering Technology (user-programmable)

Mail E-mail application (user-programmable)

Web browser Internet browser (user-programmable)

P User-programmable

"Easy-launch buttons" on page 10"Easy-launch buttons" on page 10

"

"Launch Manager" on page 44

Easy-launch button Default application

"Easy-launch buttons" on page 10

Chapter 1 15

TouchpadThe built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds as you move your finger across the surface of the touchpad. The central location on the palmrest provides optimum comfort and support.

Touchpad Basics

Use the touchpad as follows:

Move your finger across the touchpad (2) to move the cursor.

Press the left (1) and right (4) buttons located on the edge of the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad (2) is the same as clicking the left button.

Use the four-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your cursor pressing on the right scroll bar of windows applications.

NOTE: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to your finger movements: the lighter the touch, the better the response. Tapping hard will not increase

Function Left button (1) Right button (4) Main touchpad (2) Center button (3)Execute Quickly click

twice.Tap twice (at the same speed as double-clicking a mouse button).

Select Click once Tap once

Drag Click and hold. Then slide your finger across the touchpad to drag the cursor over the selection.

Tap twice (at the same speed as double-clicking a mouse button); rest your finger on the touchpad on the second tap and drag the cursor.

Access context menu

Click once

Scroll Click and hold to move up/down/left/right.

(2)

(1) (4)

(3)

(2)

(1) (4)

(3)

16 Chapter 1

the touchpad’s responsiveness.

NOTE: By default, vertical and horizontal scrolling is enabled on your touchpad. It can be disabled under Mouse settings in Windows Control Panel.

Chapter 1 17

Acer Empowering TechnologyAcer’s innovative Empowering Technology makes it easy to have access to the frequently used functions and manage the notebook. It features the following handy utilities:

Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.Acer eLock Management limits access to external storage media.Acer ePerformance Management improves system performance by optimizing disk space, memory and registry setting.Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.Acer eSettings Management accesses system information and adjusts settings easily.Acer eNet Management hooks up to location-based networks intelligently.Acer ePower Management extends battery power via versatile usage profiles.Acer ePresentation Management connects to a projector and adjusts dispaly settings conveniently.

For more information, press the key to launch the Empowering Technology menu, then click on the appropriate utility and select the Help function.

18 Chapter 1

"Easy-launch buttons" on page 10

Acer eDataSecurity Management

Acer eDataSecurity Management is a handy file encryption utility that protects the files from being accessed by unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick and easy data encryption and decryption and also supports on-the-fly file encryption for MSN Messenger and Microsoft Outlook.

There are two passwords that can be used to encrypt and decrypt a file: the supervisor password and the file-specific password. The supervisor password is a “master” password that can decrypt any file on the system. The file-specific password is assigned when you encrypt each individual file.

Acer eDataSecurity Management setup wizard will prompt for a supervisor password and default file-specific password. This file-specific password will be used to encrypt files by default, or you can choose to enter your own file-specific password when encrypting a file.

NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the supervisor password is the only other key capable of decrypting the file. If you lose both passwords, there will be no way to decrypt the encrypted files! Be sure to safeguard all related password.

Chapter 1 19

20 Chapter 1

Acer eLock Management

Acer eLock Management is a security utility that allow you to lock up your removable data, optical and floppy drives to ensure that data can not be stolen while your notebook is unattended.

Removable data devices: includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives, USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be mounted as a file system when plugged into the system.Optical drive devices: includes any kind of CD-ROM or DVD-ROM drives.Floppy disk drives: 3.5-inch disks only.

To activate Acer eLock Management, a password must be set at first. Once set, you may apply locks to any of the three kinds of devices. The lock(s) will be set without any reboot necessary, and will remain locked after rebooting, until unlocked.

If you do not set a password, Acer eLock Management will reset back to the initial status with all locks cancelled.

NOTE: If you lose the password, there is no method to reset it except by reformatting the notebook or taking the notebook to an Acer Customer Service Center. Be sure to remember or write down the password.

Chapter 1 21

Acer ePerformance Management

Acer ePerformance Management is a system optimization tool that boosts the performance of the Acer notebook. It provides you with the following options to enhance overall system performance:

Memory optimization: releases unused memory and checks memory usage.Disk optimization: removes unneeded items and files.Speed optimization: improves the usability and performance of the Windows XP system.

22 Chapter 1

Acer eRecovery Management

Acer eRecovery Management is a powerful utility with the need for recovery disks provided by the manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on the system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides:

Password protectionRecovery of applications and drivesImage or data backup:

• Backup to HDD (set recovery point)

• Backup to CD or DVDImage or data recovery tools:

• Recovery from a hidden partition (factory defaults)

• Recovery from the HDD (most recent user-defined recovery point)

• Recovery from CD or DVD

NOTE: If the computer did not come with a Recovery CD or System CD, please use Acer eRecovery Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the best results when recovering the system using a CD or Acer eRecovery Management, detach all peripherals (except external Acer ODD, if equipped), including the Acer ezDock.

Chapter 1 23

Acer eSettings Management

Acer eSettings Management allows you to inspect hardware specification and to monitor the system health status. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so your computer runs faster, smoother and better.

Provides a simple graphical user interface for navigating through the program effortlessly.Displays general system status and advanced monitoring for power users.Logs when a hardware component has been removed or replaced.Permits you to migrate personal settings.Keeps a history log of all alerts that were previously issued.

24 Chapter 1

Acer eNet Management

Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a variety of locations. To access this utility, either click on the “Acer eNet Management” icon on the notebook, or start the program from the Start menu. You also have the option to set Acer eNet Management to start automatically when you boot up the PC.

Acer eNet Management automatically detects the best settings for a new location, while offering you the freedom to manually adjust the settings to match your needs, simply by right clicking on the icon in the task bar.

Acer eNet Management can save network settings for a location to a profile, and automatically apply the appropriate profile when you move from one location to another. The settings stored include network connection settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. The security and safety concerns mean that Acer eNet Management does not store username and password information.

Chapter 1 25

26 Chapter 1

Acer ePower Management

Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower Management from the Empowering Technology interface, or double click the Acer ePower Management icon in the task tray.

AC mode

The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or click on buttons to turn the following functions on or off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio, and Wired LAN.

DC mode

To suit your usage, there are four pre-defined profiles: Entertainment, Presentation, Word Processing, and Maximum Battery. Or, you can define up to three of your own profiles.

Battery status

For real-time battery life estimates based on current usage, refer to the panel on the lower left side of the window.

You can also click “Advanced settings” to:

• Set alarms.

• Reload factory defaults.

• Select what actions will be taken when the cover is closed, and set passwords for accessing to the system after Hibernation or Stand-by.

Chapter 1 27

• View information about Acer ePower Management.

28 Chapter 1

Acer ePresentation Management

Acer ePresentation Management lets you select from two of the most common projector resolution: XGA and SVGA.

Chapter 1 29

Acer OrbiCamThe Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can transmit the best video quality over an instant messenger service.

Rotating the Acer Orbicam

The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the illustrations below:

For your convenience, the camera snaps 45 degrees to match the position of your face in front in back of the LCD panel.

NOTE: Do not rotate the camera clockwise to prevent it from the damage.

No. Item1 Lens

2 Power indicator

3 Rubber grip (selected models only)

# Item

1 2 3

# Item

30 Chapter 1

Launching the Acer OrbiCam

To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen. or Click Start > All programs > Acer > Acer OrbiCam. The Acer OrbiCam capture windows window appears as below:

Changing the Acer OrbiCam settings

Resolution

To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window, then select the desired resolution. Setting the camera resolution to 640 x 480 or larger does not change the capture window size.

Options

Click Options to display the Window, Preview, and Folder tabs. Use the options to change the capture window size, preview settings, and the folder for captured photos or videos.Options Window, Preview Folder

Chapter 1 31

Camera Settings

• Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display, then select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/Face tracking options from this window.

• Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties window will appear.

• Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness, etc.

• Advanced Settings allows you to achieve gain control, implement image mirror, select image enhancements and anti-flicker settings, and turn on/off the camera indicator.

• Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature on or off.

Capturing photos or videos

To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a Picture or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player automatically launches to display or play a preview of the photo/video clip.

NOTE: By default, all photos and videos are saved in the My Pictures and My Videos folder.

Using the Acer OrbiCam as webcam

The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application. To use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can now broadcast from your location to an IM partner anywhere in the world.

Camera Settings

Video, Audio Zoom/Face tracking

Driver Settings

Properties

Device Settings

Advanced Settings

Zoom/Face Track Settings

Camera Settings

Video, Audio Zoom/Face tracking

Driver Settings

Properties

Device Settings

Advanced Settings

Zoom/Face Track Settings

32 Chapter 1

Enabling the Acer VisageON

The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models only). The Face Tracking feature tracks your head movement and automatically centers your face in the capture window. The video effects feature allows you to select and apply an effect to your video transmissions.

NOTE: The face tracking feature is not capable of centering your face beyond the capture window frame. Minimal head movements are tracked more efficiently.

To enable the Acer VisageON:

1. Right click on this icon, then select VisageON from the pop-up menu.

The VisageON window appears as below:

2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings and options in the right section.

Using the face tracking feature

To use the face tracking feature:

1. Click the left icon down arrow button, then select Single User or Multiple Users from the pop-up menu. For multiple users, the face tracking feature automatically centers all the users’ face in the capture window, otherwise the utility centers the face of the user closest to the camera.

VisageON

Single User Multiple

Users

VisageON

Single User Multiple

Users

VisageON

Single User Multiple

Users

Chapter 1 33

2. Click the right icon to zoom in/out or reset the current view.

3. Click VisageON to display a menu that allows to change the configuration of the camera, face tracking and video effects settings.

Using video effects (selected models only)

The Video Settings section allows you to select an avatar or accessory video effect from the list. To select an effect:

1. Click the encircled icon to display the available video effects. The Video Effect Selection window appears as below:

VisageON

Using video effects

Video Settings

Video

Effect Selection

VisageON

Using video effects

Video Settings

Video

Effect Selection

VisageON

Using video effects

Video Settings

Video

Effect Selection

34 Chapter 1

2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window.

NOTE: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow screen instructions in the VisageON to continue.

NOTE: You may use video effects when using the camera for IM chat/video sessions or call conferences.

Chapter 1 35

Using the System UtilitiesNOTE: The system utilities work under Microsoft Windows XP only.

Acer GridVista (dual-display compatible)NOTE: This feature is only available on certain models.

To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.

Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on the same screen. To access this function, please go to Start > All Programs and click on Acer GridVista. You may choose any one of the four display settings indicated below:

Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer GridVista is simple to set up:

1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.

2. Drag and drop each window into the appropriate grid.

3. Enjoy the convenience of a well-organized desktop.

Note:

Start Control Panel Display

Settings (2)

Extend my windows desktop onto this monitor

Apply OK

Start All Programs Acer GridVista

Note:

Start Control Panel Display

Settings (2)

Extend my windows desktop onto this monitor

Apply OK

Start All Programs Acer GridVista

36 Chapter 1

NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value.

Launch Manager

Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access the Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.

Note:

"Easy-launch buttons" on page 24

Start All Programs

Launch Manager

Note:

"Easy-launch buttons" on page 24

Start All Programs

Launch Manager

Chapter 1 37

Start All Programs

Launch Manager

Norton AntiVirusNorton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against viruses to keep you computer data safe and secure.

How do I check for viruses?

A Full System Scan scans all files on your computer. To perform a system scan:

1. Start Norton Antivirus: Double click on the Norton AntiVirus Icon on the desktop or click on the Start menu in the Windows task bar, highlight Programs, and select Norton Antivirus.

2. In the Norton Antivirus main window, click Scans.

3. In the Scans panel, click Run Full System Scan.

4. When the scan is complete, a scan summary appears. Click Finished.

You can schedule customized virus scans that tun unattended on specific dates and times or at periodic intervals. If you are using the computer when the scheduled scan begins, it runs in the background so that you do not have to stop working.

For more information, please refer to the Norton AntiVirus Help menu.

Norton AntiVirus

Start Programs

Norton AntiVirus

Scans

Scans Run Full System Scan

Finished

38 Chapter 1

Hardware Specification and Configuration

Processor

Item SpecificationCPU type Intel® CoreTM Duo processor T2300/T2400/T2500/T2600

Intel® Celeron® M processor 410/420/430

Package Micro-FCPGA

Core voltage 1.2875V (highest frequency mode) to 0.8375V (low frequency mode)

Feature Intel® CoreTM Duo processor: Intel® Architecture with SpeedStep Technology

Bus speed 533/667 FSB operation

On-die second (L2) cache

2048KB

System Board Major Chips

Item SpecificationSystem core logic 945GM/945PM/940GML + ICH7M

Super I/O controller ICH7M LPC interface

Audio controller Codec ALC883

Video controller • UMA for 945GM and 940GML• Nvidia G72MV

HDD controller ICH7M

Keyboard controller ENE KB3910

PCMCIA controller TI7412 (with card reader and 1394 support)

soDIMM controller 945GM/945PM/940GML

Hard Disk Drive

SeagateModel ST9120821A

ST9120824AST9100824AST9100825A

ST98823AST980829A

ST96812A

Drive Specification

Formatted Gbytes (512 bytes/sector)

120 100 80 60

Physical read/write head 4 4 3 3

Discs 2 2 2 2

Spindle Speed (RPM) 4200 (ST9120824A, ST9100825A, ST980829A)5400 (ST9120821A, ST9100824A, ST98823A, ST96812A)

Internal transfer rate (Mbytes/sec. max.)

56.25 (ST9120824A, ST9100825A, ST980829A)48.25 (ST9120821A, ST9100824A, ST98823A, ST96812A)

I/O data transfer rate (Mbytes/sec. max.)

100

ATA data transfer mode supported PIO modes 0-4; Multiword DMA modes 0-2; Ultra DMA modes 0-5

Bytes per sector 512

Average latency (msec) 5.6

Chapter 1 39

Average seek, read (msec. typical) 12.5

Average seek, write (msec. typical) 14.5

Cache buffer 8 Mbytes

Interface Serial ATA

Startup current (typical, peak) +5V: 1.1 amps

Ambient temperature 5 to 55oC (operating), -40 to 70oC (nonoperating)

Temperature gradient (oC per hour max.)

20oC (operating), 30oC (nonoperating)

Relative humidity 5% to 90% (operating), 5% to 95% (nonoperating)

Relative humidity gradient 30% per hour max.

Drive acoustics, sound power (bels) idle

2.4 (typical), 2.6 (max)

Shock, operating (Gs max. at 0.5 msec.)

250

Shock, nonoperating (Gs max. at 2 msec.)

800

Vibration, operating 1.0 G (0 to peak, 5-500 Hz)

Vibration, nonoperating 5 Gs (0 to peak, 5-500 Hz)

Nonrecoverable read errors 1 per 1014 bits read, max.

Seek power (typical) 2.20 watts

Read/write power (typical) Read: 1.90 watts; Write: 2.30 watts

Idle mode, lower power (typical) 0.80 watts

Standby mode 0.28 watts

Sleep mode 0.28 watts

Voltage tolerance +5.0V +/- 5%

BIOS

Item DescriptionBIOS vendor Phoenix

System BIOS version V1.00

Feature • Suspend to RAM (S3) / Disk (S4)• Support boot option: HDD / Removable device (media bay device) /

all USB ports• Support SMBIOS 2.3, PCI2.2, WFM2.0• ACPI 2.0/3.0 compliance with Intel Speedstep Support C1, C2, C3,

C4 and S3, S4 for mobile CPU• Wake on LAN from S3• Wake on LAN from S4 in AC mode• Package: 40-pin TSOP• ROM type: one MB CMOS Boot block Flash Memory

Hard Disk Drive

Seagate

40 Chapter 1

System Memory

Item DescriptionChipset 945GM/945PM/940GML

Feature • DDR2 400/533/667 MHz SDRAM memory interface design• Two DDR SODIMM slots• Maximum memory up to 4GB (with two 2GB SODIMM)• Dual Channel

VGA

Item UMA DiscreteChip 945GM/940GML Nvidia G72MV

VRAM up to 128MB up to 256MB

PCMCIA

Item DescriptionPCMCIA controller TI7412

Card type support Type II

Number of slot One

Feature Five-in-one Card Reader: Memory Stick (MS), Memory Stick Pro (MS PRO), MultiMediaCard (MMC), Secure Digital (SD) and xD-Picture Card (xD).

Audio

Item DescriptionAudio controller Realtek ALC833 Azadia Codec

Feature • Built-in• Stereo• SNR > 85, high-performance DACs with 95dB SNR (A-Weighting),

ADCs with 85dB SNR (A-Weighting)• Internal Microphone• Two speakers, at least 1.5W / 30cc for each• 2* digital microphone array• VoIP function support• Universal jack function support

LAN

Item DescriptionLAN controller Realtek RTL8111B

Feature • 10 / 100 / 1000 Mbps PCI LAN• Jumbo frame support• WOL from S5 support• File deployment support

Chapter 1 41

Connector type RJ-45

Wireless LAN

Item DescriptionCard type Mini-PCI

Mode • 802.11a/b/g• 802.11b/g• Built-in two antenna (placed on the top of LCD on the side of LCD

latch, the wire of antenna can not be placed under the panel)

Support Wi-Fi, WPA2, WMM, CCX V3/V4

Modem

Item DescriptionController ICH7M

Data modem data baud rate (bps)

56K

Modem/bluetooth protocol supported

• V.90/V.92 AC-Link modem with PTT approval• Wake-on-Ring ready• CISPR22 application

Connector type RJ-11

Keyboard

Item DescriptionController ENE KB3910

Model name New Acer Ergo Keyboard

Feature • 105 / 106 keys standard keyboard• Touch pad with 4-way integrated scroll button• Windows keys and application keys support• Standard pitch, 2.5 mm travel length• Hotkey controls• Embedded numeric keypad• Multi-language support• Spill-proof• Four easy-launch buttons: Internet browser, E-mail with LED, Acer

Empowering, one user-programmable button

Battery

Item SpecificationVendor & model name Panasonic / Sanyo / Sony

Battery Type Li-Ion

LAN

Item Description

42 Chapter 1

Pack capacity 8-cell: 2400 mAh6-cell: 2000 mAh

System Power Management

Legacy Mode ACPI ModeOff • Mech. Off (G3): All devices in the system are turned off completely.

• Soft Off: (G2/S5): All devices in the system are turned off completely by OS shutdown.

On • Working (G0/S0): Individual devices such as the CPU and hard disk may be power-managed in this state.

• S3 Sleeping State: CPU set power down, VGA suspend, PCMCIA suspend, Audio power down, HDD power down, CD-ROM power down, Super I/O low power mode.

• S4 Sleeping State: It is also called hibernation state. The system saves all system setting and data onto disk before the whole system is powered off.

LCD

Item SpecificationVendor and Model name

Samsung LTN170WX-L05-H

QDI QD17TL02-06

AUOB170PW03 V4

LGLP171WP4-TL02

Screen Diagonal (mm)

17.1” WXGA 17.1” WXGA 17.1” WXGA 17.1” WXGA

Active area 367.20 (W) x 229.50 (H)

367.20 (W) x 229.50 (H)

367.20 (W) x 229.50 (H)

367.20 (W) x 232.9 (H)

Display resolution 1440 x 3 (RGB) x 900

1440 x 3 (RGB) x 900

1440 x 3 (RGB) x 900

1440 x 3 (RGB) x 900

Display mode normally white normally white normally white normally white

Surface treatment non-glare type (1) glare type (H)

hard coating (3H) glare type

glare type glare type

Pixel arrangement

RGB vertical stripe

RGB vertical stripe

RGB vertical stripe

RGB vertical stripe

Pixel pitch (mm) 0.255 (per one triad) x 0.255

0.255 (per one triad) x 0.255

0.255 (per one triad) x 0.255

0.255 (per one triad) x 0.255

Typical white luminance (cd/m2) also called brightness

200 (typical) 200 (center typical)

200 (typical) 200 (typical)

Contrast ratio 350 (typical) 300 : 1 (Min) 300 : 1 (typical) 350 (Min)

Respond time (optical rise time + fall time) (msec.)

25 (typical)35 (max.)

25 (typical) 16 (typical) 25 (typical)

Normal input voltage of power supply

+3.3V (typical) +3.3V (typical) +3.3V (typical) +3.3V (typical)

Battery

Item Specification

Chapter 1 43

AC Adaptor

24X Combo Drive Interface

Power consumption (watt)

4.320 (typical) 4.7 (typical) 8 (max.) 4.78 (typical)

Weight 750g 750g 700g 670g

Physical size (mm)

382.7 (W) x 245 (V) x 7.0 (T)

382.7 (H) x 245.1 (V) x 7.0 (T)

382.2 (W) x 244.5 (H) x 6.6 (D)

382.2 (W) x 244.5 (H) x 6.5 (D)

Electrical interface

2 channel LVDS 2 channel LVDS 2 channel LVDS 2 channel LVDS

Color support Native 262K colors

Native 262K colors

Native 262K colors

Native 262K colors

Item SpecificationModel name LiteOn PA-1900-04AW Delta 90W ADP-90SB BBAA

Input feature

Rated voltage for 100Vac or 240Vac input AC voltage

for 100Vac or 240Vac input AC voltage

Input voltage range from 90Vac to 264Vac from 90Vac to 265Vac

Rated frequency for 50Hz or 60Hz for 50Hz or 60Hz

Frequency range from 47Hz to 63Hz from 47Hz to 63Hz

Steady AC current less than 1.5A rms at 100Vac input and maximum load

less than 1.5A rms at 100Vac input and maximum load

Output feature

Rated voltage 19V 19V

Voltage range 18.05V to 20V from 18.2V to 19.8V

Rated power 90 W 90 W

Output ripple and noise less than 300mVp-p less than 300mVp-p

Turn on delay time within two seconds at 115 Vac input voltage

within two seconds at 115 Vac input voltage

Temperature Operating: 0 to 40oCNon-operating: -31 to 60oC

Operating: 0 to 40oCNon-operating: -31 to 60oC

Item SpecificationVendor & model name PHILIPS SCB5265 LITEON SSC-2485K

Performance Specification

Transfer rate (KB/sec.) Sustained:DVD: Max 10.56Mbytes/sec.CD: 3600Kbytes/sec.

Sustained:DVD: Min 10.15Mbytes/sec.CD: 3500 Kbytes/sec.

LCD

Item Specification

44 Chapter 1

8X DVD Dual Interface

Access Time (Typical) DVD: Random Access: 125 msDVD: Full Stroke: 165msCD: Random Access:105msCD: Full Stroke:160ms

DVD: Random Access: 100 msDVD: Full Stroke: 190msCD: Random Access:95msCD: Full Stroke:180ms

Buffer Memory 2MB 2MB

Interface Compliant to ATA/ATAPI-5 ATA/ATAPI-6, MMC-3 and SFF8090 Ver5, Revision 1.2.

Applicable disc format DVD (read): DVD 5, 9, 10, 18, DVD-ROM, DVD-Video, DVD-R 3.95G, DVD-R 4.7G, DVD-RW, DVD+R, DVD+RW, Multi-Border DVD-R/DVD-RW, Multi-Session DVD+R, DVD+RW, DVD-RAMCD (write): CD-DA, CD ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2, CD-I, Video-CD (MPEG-1), CD-TextCD (write): CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2, CD-i, Video-CD, CD-Text

CD: CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1 and Form-2, CD-I Ready, Video-CD(MPEG-1), Karaoke-CD, PhotoCD (Multi-Session), Enhance CD, CD extra, I-Trax CD and UDF

Loading mechanism Load: Manual load Manual load/DC brushless motor system

Power Requirement Max. 1300mA Max. 1200mA

Input Voltage 5 V +/- 5% (Operating) 5 V +/- 5% (Operating)

Item SpecificationVendor and model name PHILIPS SDVD8441

Performance specification

Transfer rate (KB/sec.) Sustained:DVD:10.9Mbytes/sec. (Typ)CD: 3650Kbytes/sec. (Typ)

Access time (typical) DVD: Random Access: 130 msDVD: Full Stroke: 240msCD: Random Access:130msCD: Full Stroke:240ms

Buffer memory 2MB

Interface ATA/ATAPI-5

Item Specification

Chapter 1 45

8X Super Multi Interface

Applicable disc format DVD (read): DVD-ROM 5,9,10,18, DVD-VIDEO, DVD-AUDIO, DVD-R, DVD-R 3.95G, DVD-R MULTI BORDER, DVD-RW, DVD+R, DVD+R DL, DVD+R MULTI-SESSION, DVD+RWCD (read): CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 Form-2, CD-I, CD-I Bridge, Video-CD(MPEG-1), Karaoke CD, Photo-CD, Enhanced CD, CD Plus, CD Extra, i-trax CD, CD-Text, CD-R, and CD-RWDVD (write): DVD Data & VideoCD (write): CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2, CD-i, Video-CD, CD-Text

Loading mechanism Load: manual load

Power consumption Max. 1500 mA

Input voltage 5V +/- 5% (operating)

Item SpecificationVendor and model name Liteon SSM 8515S Pioneer DVR-K06RS Philip SDVD-8821

Performance Specification

Transfer rate read (KB/sec.)

Sustained:• DVD: 10.00Mbytes/

sec.• CD: 3500kbytes/sec.

Sustained:• DVD: 10.80Mbytes/

sec.• CD: 3600kbytes/sec.

Sustained:• DVD: 10.90Mbytes/

sec.• CD: 3650kbytes/sec.

Access time / Seek time • DVD: random access 130ms

• DVD: full stroke 250ms

• CD: random access 110ms

• CD: full stroke 220ms

• Access time: DVD 160 msec; CD 150 msec.

• Random seek time: DVD 150 msec; CD 140 msec.

• Full stroke seek time: DVD 300 msec; CD 290 msec.

• Random access: DVD 130ms; CD 130ms

• Full stroke: DVD 200ms; CD 240ms

Buffer memory 2MB 2MB 2MB

Interface compliant to ATA/ATAPI-6, MMC-4 and SFF8090 Ver5

compliant to SFF8020, SFF8090

compliant to ATA/ATA-5

Item Specification

46 Chapter 1

Applicable disc format CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2, CD-I, Video-CD (MPEG-1), CD-Text, PhotoCD, Enhance CD, CD extra, I-Trax CD and UDF DVD-ROM, DVD-Video, DVD-Audio, DVD-R single/multi border, DVD+R single/multi session, DVD-RW, DVD+RW, DVD-RAM

KODAK Photo CD single and multi-session, CD Extra (CD PLUS), Video CD, CD text data (read/write), CD-R (read/write), DVD-ROM, DVD-R (read/write), DVD-R DL (read/write), DVD-RW (read/write), DVD+RW (read/write), DVD+R (read/write), DVD+R DL (read/write), DVD+RW (read/write), DVD+RW high speed (read/write), DVD-RAM (read/write)

• DVD read: DVD-5, DVD-9, DVD-10, DVD-18, DVD-Video, DVD-Audio, SACD (Hybrid), DVD-R, DVD-R DL, DVD-R 3.95GB, DVD-R Authoring, DVD-R multi-border, DVD-RW, DVD+R, DVD+R DL, DVD+R Multi-session, DVD+RW, DVD-RAM V1.0, DVD-RAM V2.1; CD read: CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2, CD-i, CD-i Bridge, Video-CD (MPEG-1), Karaoke CD, Photo-CD, Enhanced CD, CD Plus, CD Extra, i-trax CD, CD-Text, CD-R, CD-RW

• DVD write: DVD Data, DVD-video; CD write: CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2, CD-i, Video-CD, CD-text

Loading mechanism Load: manual load/DC brushless motor system

N/A N/A

Power requirement Max. 1500mA Max. 1800mA Max. 1300mA

Input voltage +5V +/- 5% (operating) +5V +/- 5% (operating)+5V +/- 8% (start-up)

+5V +/- 5% (operating)

Item Specification

Chapter 1 47

System Utilities

Chapter 2

BIOS Setup UtilityThe BIOS Setup Utility is a hardware configuration program built in the BIOS (Basic Input / Output System) of computer. Generally speaking, the computer is already properly configured and optimized, and you do not need to run this utility.

However, if you encounter configuration problems, you may need to run Setup. Otherwise, you can also refer to Chapter 4 Troubleshooting when problem arises.

Invoking BIOS Setup

To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted on the left-bottom side of the screen).

There are six prime items in the BIOS Setup Utility. They are Information, Main, Advanced, Security, Boot and Exit. In the coming pages, we will explain the BIOS Setup Utility by item.

NOTE: During setup, all Fn function keys and power saving function are disabled.

Part DescriptionInformation Display the system informations.

Main Allows the user to specify standard IBM PC AT system parameters.

Security Provides security setting of the system.

Boot Allows the user to specify the boot options.

Exit Allows the user to save CMOS setting and exit Setup.

Chapter 2 48

Information

CPU type: This item will show the CPU information of the system.CPU speed: This item will show the COU clock speed.IDE1 model name: This item will show the model name of HDD installed on primary IDE master. The hard disk model name is automatically detected by the system. If there is no hard disk present or unknown type, “None” should be shown on this field.IDE1 serial number: This item will show the serial number of HDD installed on Primary IDE master. If no hard disk or other devices are installed on primary IDE master, it will display a blank line.System BIOS version: This field reports BIOS version of the system.KBC version: This field reports keyboard controller version of the system.Serial Number: This item is the serial number of the system.Asset Tag Number: This item is the asset tag number of the system.UUID: It shows only when an internal LAN device is available.

49 Chapter 2

Main

System Time and System Date:

The hours are displayed with 24-hour format. The changes in these two items take effect immediately.System Memory:

This item reports the memory size of system base memory. The size is fixed to 640KB.Extended Memory:

It reports the memory size of the extended memory in the system. The extended memory size is equal to total memory size (one MB).Video Memory:

It indicates the video memory size.Quiet Boot:

• Enabled: Customer Logo is displayed, and Summary Screen is disabled.

• Disabled: Customer Logo is displayed, and Summary Screen is enabled.Power on Display:

• Auto: During power on process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be only in CRT (or projector) mode. Otherwise, it will be in LCD mode.

• Both: Both the integrated LCD and the external video port (for an external CRT or projector)

Chapter 2 50

will be enabled simultaneously.Network Boot:

It permits the users to boot from network.F12 Boot Menu:

• Enabled: When it is enabled, the users can modify device boot priority by pressing <F12> during POST.

• Disabled: When it is not enabled, device boot priority will not be adjustable during POST.

The boot device change is only for one-time change. In other words, when the system is rebooted, the boot device sequence will be the same as the one defined in the BIOS setup (Boot option).D2D Recovery:

It allows the users to enable or disable the disk-to-disk recovery.

51 Chapter 2

Security

The system supports three levels of password protection. The password support consists of a Supervisor Password, User Password, and Hard Disk Password. All the passwords are stored in a non-volatile storage device (EEPROM).

Password Policy:

All the passwords will obey the following rules:

• All the passwords can be set or cleared in BIOS Setup Security screen.

• The password entry consists of eight alphanumeric characters. At least one character must be assigned.

• The valid keys are listed in the table below:

Symbol Character Symbol NameA-Z letters A to Z (not case sensitive)

0-9 numerical characters

- dash

= equal sign

[ left bracket

] right bracket

Chapter 2 52

• The users can not change or remove password during resuming from S4.

• The max. number of times to retry the password is limited to three.Supervisor Password:

Supervisor Password controls the access of the whole BIOS Setup Utility. If the Supervisor Password is set, the system will pop up the password dialog box to ask for the password when the users press <F2> for entering BIOS Setup Utility.

If the Supervisor Password is set and Password on boot is enabled, the system will pop up the password dialog box to ask for the password when the system is powered on or resumes for S4 state.

If the users fail three times consecutively in password verification, the system will be hung up and the users need to manually power off the system. User Password:

If the User Password is set, the system will pop up the password dialog box to ask for the password when the users press <F2> for entering BIOS Setup Utility.

If the Supervisor Password is not set at first, the User Password can not be set. If the Supervisor Password is cleared, the User Password will be cleared, too.

If the User Password is set and Password on boot is enabled, the system will pop up the password dialog box to ask for the password when the system is powered on or resumes for S4 state.

If the users fail three times consecutively in password verification, the system will be hung up and the users need to manually power off the system.Set Supervisor Password / User Password:

1. Highlight the item and press “Enter”, a dialog box will be shown to ask the users to enter new password and confirm new password.

2. If the users want to reset password, a current password will be required to be tapped in at first. If the current password is correct, the users are permitted to enter new password and confirm new password for verification. If the verification is OK, the password setting will be complete after the users press “Enter”.

3. If the password entered does not match the current password, a dialog box will be shown to ask to re-enter the password.

Set HDD Password: When shown as “Locked”, the hard drive password currently can not be changed or disabled. To change or disable it, turn off the system and enter Setup immediately after turning it back on. Press “Enter” to input change, or disable hard drive password.Password on Boot:

It allows the user to specify whether or not a password is required to boot.

. period

, comma

; semi-colon

/ slash

\ back slash

Symbol Character Symbol Name

53 Chapter 2

Boot

This menu allows the users to decide the order of bootable devices to load the operating system. It identifies all the bootable devices in the system and attempts to boot them in the order specified. Bootable devices include the diskette drive in module bay, the hard disk and the CD-ROM/DVD drive in module bay and onboard LAN device.

Chapter 2 54

Exit

Exit Saving Changes:

It allows the users to save changes to CMOS and reboot the system. Exit Discarding Changes:

The users can exit the Setup not to save changes.Load Setup Defaults:

It allows the users to load default values in CMOS Setup.Discard Changes:

The users can discard previous changes in CMOS Setup.Save Changes:

The users can save current changes in CMOS Setup.

55 Chapter 2

Machine Disassembly and Replacement

Chapter 3

This chapter contains step-by-step procedures on how to disassemble the notebook for maintenance and troubleshooting.

To disassemble the computer, you need the tools below:

Wrist ground strap and conductive mat for preventing electrostatic discharge

Small Philips screw driver

Flat head screw driver

Hexagonal driver

TweezersNOTE: The screws for the different components vary in size. During the disassembly process, group the

screws with the corresponding components to avoid mismatch when putting back the components. When you remove the stripe cover, please be careful not to scrape the cover.

Chapter 3 56

General Information

Before You Begin

Before proceeding with the disassembly procedure, you have to make sure that:

1. The system and all peripherals are powered off.

2. The AC adaptor and all power and signal cables from the system are unplugged.

3. The battery pack is removed.NOTE: There are several types of screws used to secure the main unit. The screws vary in length. Please

refer to the screws table after the flowchart. Group the same type of screws together during service disassembling. Please also remember the screw location for each screw type. If you fasten the screws on the wrong location, the long screws may cause irrecoverable damage to the main board.

57 Chapter 3

Disassembly Procedure FlowchartThe flowchart gives you a graphic representation on the entire disassembly and reassembly and instructs you how to remove the components.

Screws List

No. Description Part No.a SCW HEX NYL I#R-40/O#4-40 L5.5 34.00015.081

b SCREW MACH WAFER M2*L4 NI 86.T39V1.002

c SCRW M2.5*6 ~ L-CASE + U-CASE 86.00D28.330

d SCRW M2*L3 86.00D29.620

e SCRW M2.5*5 WAFER B-ZN ROHS 86.00D47.630

f SCREW M2*L3 NYLOK CR 3+ 86.00E25.723

Chapter 3 58

g SCREW M2*L3 NON-NYLOK CR3+ 86.00E31.723

h SCREW M2.5*L6 NYLOK CR3+ 86.00E33.736

i SCREW M2.5*L8 NYLOK CR3+ 86.00E34.738

j SCREW M2*L8 NI NON-NYLOK 86.00E35.228

k SCREW M3x4(86.9A524.4R0) 86.9A524.4R0

l SCRW M2*4 WAFER NI 86.9A552.4R0

m SCREW NI M2*6L 86.9A552.6R0

n SCRW M2.5*L3(NON NYLOK) 86.9A523.3R0

Screws List

No. Description Part No.

59 Chapter 3

Disassembly Procedure

Removing the Battery Pack

1. Unlock the battery pack.

2. Slide the battery latch, hold it then remove the battery.

Removing the HDD Module

1. Release the three screws fastening the HDD module cover.

2. Detach the HDD module cover.

3. Release the two screws holding the HDD module then pull the HDD module as arrow indicates and remove the HDD module.

Chapter 3 60

Removing the MiniPCI Card and the Memory

1. Release the two screws securing the miniPCI cover.

2. Remove the miniPCI cover.

3. Disconnect the wireless antenna then remove the wireless LAN card.

4. Release the two screws securing the RAM cover and remove the RAM cover.

5. Press the left and right latches to pop up the memory.

61 Chapter 3

Removing the Keyboard

1. Open the notebook as shown.

2. Remove the middle cover.

3. There are four latches securing the keyboard.

4. Push those latches by the screw driver as shown and the keyboard will pop up a little.

5. Remove the keyboard and reverse it.

6. Carefully pull the keyboard FFC lock, then disconnect the keyboard FFC.

Chapter 3 62

Separating the LCD Module and Main Unit

1. Pull carefully and disconnect the LCD cable.

2. Tear off the tape securing the wireless antenna and pull out the wireless antenna.

3. Release the two screws securing the LCD hinges on the bottom side.

4. Release the two screws fastening the LCD hinges on the rear side.

5. Release the two screws holding the LCD hinges as shown.

6. Then separate the LCD module from the main unit.

63 Chapter 3

Disassembling the Main Unit

Separating the Upper Case and the Lower Case

1. Release the connector lock and disconnect the touch pad FFC.

2. Release the connector lock and disconnect the function keyboard FFC.

3. Release the three screws securing the upper case.

4. Release the 27 screws holding the lower case.

5. Lift the upper case carefully and disconnect the lid switch cable.

6. Then separate the upper and the lower case.

Chapter 3 64

Removing the Function Keyboard

1. Release the FFC lock and disconnect the function keyboard FFC.

2. Release the four screws holding the function keyboard bracket.

3. Then remove the function keyboard bracket.

4. Carefully disconnect the microphone cable and remove the function keyboard.

65 Chapter 3

Removing the Touch Pad Board

1. Carefully release the FFC lock and disconnect the touch pad board FFC.

2. There are 13 latches holding the touch pad bracket.

3. Unlock those latches with a screw driver as shown then detach the touch pad bracket.

4. Detach the touch pad board.

Chapter 3 66

Removing the ODD Module and Dummy Card

1. Slightly pull the ODD module and remove it.

2. Pull the dummy card from the slot and remove it.

Removing the Main Board

1. Disconnect the fan cable.

2. Disconnect the speaker cable and Bluetooth module cable.

3. Remove the four screws securing the main board.

4. Then detach the main board from the lower case.

67 Chapter 3

Removing the System Fan

1. Release the two screws holding the heatsink.

2. Remove the heatsink.

Removing the Bluetooth Module

1. Detach the bluetooth module from the lower case.

2. Carefully disconnect the bluetooth module cable.

Chapter 3 68

Removing the Speakers

1. Release the four screws securing the left and right speakers.

2. Remove the speakers from the lower case.

Removing the MDC Module

1. Carefully disconnect the MDC cable.

2. Release the two screws securing the MDC board then detach the MDC board.

3. Disconnect the MDC board cable.

69 Chapter 3

Remove the Heatsink Module

1. Release the five screws securing the heatsink.

2. Remove the heatsink module.

Removing the CPU

1. Release the screw counter clockwise with a flat screw driver.

2. Detach the CPU from the CPU socket.

Chapter 3 70

LCD Disassembly

1. Remove the eight rubber caps on the LCD bezel and release the eight screws securing the LCD bezel.

2. Detach the LCD bezel from the LCD module as shown.

3. Release the screw holding the inverter board.

4. Disconnect the inverter board cables as shown and remove the inverter board.

71 Chapter 3

5. Release the four screws securing the LCD panel.

6. Detach the LCD panel carefully and reverse it as shown.

7. Tear off the tapes holding the LCD panel cable carefully then disconnect the LCD panel.

8. Remove the antenna from the LCD cover.

Chapter 3 72

9. Release the four screws securing the left LCD bracket then remove the left LCD bracket.

10. Repeat the anterior step to remove the right LCD bracket.

73 Chapter 3

11. Release the screw holding the CCD module and carefully pull the CCD module cable and LCD cable through the latch bar and LCD cover.

12. Remove the CCD module cap.

13. Remove the CCD module ring.

14. Push the CCD module upper case a little bit.

15. Then Separate the lower case from the upper case.

16. Release the two screws holding the CCD module board the detach the CCD module board.

Chapter 3 74

Troubleshooting

Chapter 4

Please use the following procedures as a guide for computer problems.

NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options may occur errors or invalid responses.

1. Obtain the detailed fail symptoms as many as possible.

2. Verify the symptoms by attempting to recreate, running the diagnostic tests or repeating the same operation.

3. Disassemble and assemble the unit without any power sources.

4. If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You can check the following:

Power cords are properly connected and secured;

There are no obvious shorts or opens;

There are no obviously burned or heated components;

All components appear normal.

Chapter 4 75

System Check Procedures

External Diskette Drive Check

Do the following procedures to isolate the possible effects from a controller, driver, or diskette. A writable, diagnostic diskette is required.

NOTE: Make sure that the diskette does not have more than one label attached. Multiple labels may cause damage to the drive or make the drive fail.

1. Boot from the diagnostic diskette and start the diagnostic programs.

2. See if FDD test is passed as the programs run the FDD test.

3. Follow the instructions in the message window.

If errors occur with the internal diskette driver, reconnect the diskette connector on the system board. If the errors still remain:

1. Reconnect the external diskette drive.

2. Replace the external diskette driver.

3. Replace the main board.

External CD-ROM Drive Check

Do the following procedures to isolate the possible effects from a controller, driver, or CD-ROM.

NOTE: Make sure that the CD-ROM does not have any label attached. The label may cause damage to the drive or make the drive fail.

1. Boot from the diagnostic diskette and start the diagnostic programs.

2. See if CD-ROM test is passed when the programs run the CD-ROM test.

3. Follow the instructions in the message window.

If errors occur, reconnect the connector on the system board. If the errors still remain:

1. Reconnect the external CD-ROM drive.

2. Replace the external CD-ROM drive.

3. Replace the main board.

Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is under test. If the internal keyboard does not work or an unexpected error appears, make sure that the flexible cable extending from the internal keyboard is correctly connected on the system board. If the keyboard is correctly connected, run the Keyboard test.

If errors occur, do the following procedures in sequence to correct the problems. Do not replace a non-defective FRU.

1. Reconnect the keyboard cable.

2. Replace the keyboard.

3. Replace the main board.

The following auxiliary input devices are supported by this computer.

76 Chapter 4

Numeric keypadExternal keyboard

If any of these devices do not function, reconnect the cable and repeat the anterior procedures.

Memory Check

Follow the procedures below to correct the memory errors.

1. Boot from the diagnostic diskette and start the diagnostic programs.

2. Go to the diagnostic memory in the test items.

3. Press F2 in the test items.

4. Follow the instructions in the message window.NOTE: Make sure that the DIMM is correctly inserted into the connector. A wrong connection will cause

errors.

Power System Check

To verify the symptoms, power on the computer by using the following power sources separately.

1. Remove the battery pack.

2. Connect the power adaptor and check the power supply.

3. Disconnect the power adaptor and install the battery pack, then check the power supply.

If you think there is a power supply problem, please go to “Check the Power Adaptor” and “Check the Battery Pack” in this chapter.

Check the Power Adaptor

Unplug the power adaptor cable from the computer and measure the output voltage at the plug of the power adaptor cable. See the illustration and follow the procedures below.

1. If the voltage is not correct, replace the power adaptor.

2. If the voltage is within the range:

(1) Replace the system board.

(2) If the problem is still not resolved, see “Undetermined Problems”.

(3) If the voltage is not correct, go to the next step.NOTE: An audible noise from the power adaptor does not always indicate a defect.

3. If the power-on indicator does not light up, check the power cord of the power adaptor for continuity and correct installation.

4. If the operational charge does not work, see “Check the Battery Pack”.

pin 1: +19V to +20.5Vpin 2: 0V, ground

Chapter 4 77

Check the Battery Pack

Follow the procedures below to check the battery pack.

From software, this helps to identify the problem is on recharging or discharging.

1. Check the Power Management in Control Panel.

2. Then confirm that the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct.

3. Repeat the step 1 and step 2 for both battery and adaptor.

From hardware, this helps to identify whether you should replace the battery pack or not.

1. Power off the system.

2. Remove the battery pack and measure the voltage between terminals one (+) and seven (-). There are seven terminals totally. See the illustration below.

3. If the voltage is still less than 7.5V after recharging, replace the battery.

If the battery status indicator does not light up, remove the battery pack. After the battery pack returns to room temperature, reinstall it to the system.

If the charge indicator does not light up, replace the battery pack. If the charge indicator still does not light up, replace the AC/DC charger board.

Touchpad Check

If the touchpad does not work, follow the procedures one at a time to correct the problem. Do not replace a non-defective FRU.

1. After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.

2. Run utility with the PS/2 mouse function and check if the mouse is working.

78 Chapter 4

3. If the PS/2 mouse does not work, then click if the main board to switch board FPC is connected properly.

4. If the main board to switch board FPC is connected correctly, then check if the FFC on the touch pad PCB is connected properly.

5. If the FFC on the touch pad PCB is connected correctly, check if LS851 JP1 Pin6 = 5V are pules. If yes, then replace switch board. If not, then go to the next step.

6. Replace the touch pad PCB.

7. If the touch pad still does not work, then replace the FPC on Track Pad PCB.

After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement will occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No actions are necessary to be taken if the pointer movement stops in a short period of time.

Chapter 4 79

Power-On Self-Test (POST) Error MessageThe POST error message index lists the error message and their possible causes.

NOTE: Perform the FRU replacement or actions in the sequence shown in Error Message List, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.

The error messages are listed in the coming pages to indicate the BIOS signals on the screen and the error symptoms classified by functions. If the symptom is not included on the list, please refer to “Undetermined Problems”.

NOTE: Most of the error messages occur during POST. Some of them show information about a hardware device, for example, the size of memory installed. Others may indicate problems with a device, such as the way it has been configured.

NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, please reset the computer. Enter Setup and install Setup defaults to correct the errors.

80 Chapter 4

Index of Error Messages

Error Message List

Error Messages FRU/Action in SequenceStruck Key See “Keyboard or Auxiliary Input Device Check“.

System CMOS checksum bad - Default configuration used

RTC batteryRun BIOS Setup Utility to reconfigure system, then reboot system.

Real time clock error RTC batteryRun BIOS Setup Utility to reconfigure system time, then reboot system.Main board

Previous boot incomplete - Default configuration used

“Load Default Settings” in BIOS Setup Utility.RTC batteryMain board

Invalid System Configuration Data “Load Default Settings” in BIOS Setup Utility.Main board

Operating system not found Enter Setup and see if fixed disk and drive A are properly identified.Diskette driveHard disk driveMain board

Power-on indicator turns off and LCD is blank.

Power source (battery pack and power adapter.) See “Power System Check“.Ensure every connector is connected tightly and correctly.Reconnect the DIMM.Main board.

Power-on indicator turns on and LCD is blank.

Power source (battery pack and power adapter.) See “Power System Check“.Reconnect the LCD connectorHard disk driveLCD cableLCD inverterLCDMain board

Power-on indicator turns on and LCD is blank. But you can see POST on an external CRT.

Reconnect the LCD connectors.LCD cableLCD inverterLCDMain board

Power-on indicator turns on and a blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly.Main board

Chapter 4 81

Phoenix BIOS Beep Codes

Code Beeps POST Routine Description02h Verify Real Mode

03h Disable Non-Maskable Interrupt (NMI)

04h Get CPU type

06h Initialize system hardware

07h Disable shadow and execute code from the ROM.

08h Initialize chipset with initial POST values

09h Set IN POST flag

0Ah Initialize CPU registers

0Bh Enable CPU cache

0Ch Initialize caches to initial POST values

0Eh Initialize I/O component

0Fh Initialize the local bus IDE

10h Initialize Power Management

11h Load alternate registers with initial POST values

12h Restore CPU control word during warm boot

13h Initialize PCI Bus Mastering devices

14h Initialize keyboard controller

16h 1-2-2-3 BIOS ROM checksum

17h Initialize cache before memory autosize

18h 8254 timer initialization

1Ah 8237 DMA controller initialization

1Ch Reset Programmable Interrupt Controller

20h 1-3-1-1 Test DRAM refresh

22h 1-3-1-3 Test 8742 Keyboard Controller

24h Set ES segment register to 4 GB

28h Autosize DRAM

29h Initialize POST Memory Manager

2Ah Clear 215 KB base RAM

2Ch 1-3-4-1 RAM failure on address line xxxx

2Eh 1-3-4-3 RAM failure on data bits xxxx of low byte of memory bus

2Fh Enable cache before system BIOS shadow

32h Test CPU bus-clock frequency

33h Initialize Phoenix Dispatch Manager

36h Warm start shut down

38h Shadow system BIOS ROM

82 Chapter 4

3Ah Autosize cache

3Ch Advanced configuration of chipset registers

3Dh Load alternate registers with CMOS values

41h Initialize extended memory for RomPilot.

42h Initialize interrupt vectors

45h POST device initialization

46h 2-1-2-3 Check ROM copyright notice

47h Initialize I20 support

48h Check video configuration against CMOS

49h Initialize PCI bus and devices

4Ah Initialize all video adapters in system

4Bh QuietBoot start (optional)

4Ch Shadow video BIOS ROM

4Eh Display BIOS copyright notice

50h Display CPU type and speed

51h Initialize EISA board

52h Test keyboard

54h Set key click if enabled

55h Enable USB devices

58h 2-2-3-1 Test for unexpected interrupts

59h Initialize POST display service

5Ah Display prompt “Press F2 to enter SETUP”

5Bh Disable CPU cache

5Ch Test RAM between 512 and 640 KB

60h Test extended memory

62h Test extended memory address lines

64h Jump to User Patch1

66h Configure advanced cache registers

67h Initialize Multi Processor APIC

68h Enable external and CPU caches

69h Setup System Management Mode (SMM) area

6Ah Display external L2 cache size

6Bh Load custom defaults (optional)

6Ch Display shadow-area message

6Eh Display possible high address for UMB recovery

70h Display error messages

72h Check for configuration errors

76h Check for keyboard errors

Code Beeps POST Routine Description

Chapter 4 83

7Ch Set up hardware interrupt vectors

7Eh Initialize coprocessor if present

80h Disable onboard Super I/O ports and IRQs

81h Late POST device initialization

82h Detect and install external RS232 ports

83h Configure non-MCD IDE controllers

84h Detect and install external parallel ports

85h Initialize PC-compatible PnP ISA devices

86h Re-initialize onboard I/O ports

87h Configure Motherboard Configurable Devices (optional)

88h Initialize BIOS Data Area

89h Enable Non-Maskable Interrupts (NMIs)

8Ah Initialize Extended BIOS Data Area

8Bh Test and initialize PS/2 mouse

8Ch Initialize floppy controller

8Fh Determine number of ATA drives (optional)

90h Initialize hard-disk controllers

91h Initialize local-bus hard-disk controllers

92h Jump to UserPatch2

93h Build MPTABLE for multi-processor boards

95h Install CD ROM for boot

96h Clear huge ES segment register

97h Fixup Multi Processor table

98h 1-2 Search for option ROMs. One long, two short beeps on checksum failure.

99h Check for SMART drive (optional)

9Ah Shadow option ROMs

9Ch Set up Power Management

9Dh Initialize security engine (optional)

9Eh Enable hardware interrupts

9Fh Determine number of ATA and SCSI drives

A0h Set time of day

A2h Check key lock

A4h Initialize Typematic rate

A8h Erase F2 prompt

AAh Scan for F2 key stroke

ACh Enter SETUP

AEh Clear Boot flag

B0h Check for errors

Code Beeps POST Routine Description

84 Chapter 4

B1h Inform RomPilot about the end of POST.

B2h POST done- prepare to boot operating system

B4h 1 One short beep before boot

B5h Terminate QuietBoot (optional)

B6h Check password (optional)

B7h Initialize ACPI BIOS

B9h Prepare Boot

BAh Initialize SMBIOS

BBh Initialize PnP Option ROMs

BCh Clear parity checkers

BDh Display MultiBoot menu

BEh Clear screen (optional)

BFh Check virus and backup reminders

C0h Try to boot with INT 19

C1h Initialize POST Error Manager (PEM)

C2h Initialize error logging

C3h Initialize error display function

C4h Initialize system error handler

C5h PnPnd dual CMOS (optional)

C6h Initialize notebook docking (optional)

C7h Initialize notebook docking late

C8h Force check (optional)

C9h Extended checksum (optional)

CAh Redirect Int 15h to enable remote keyboard

CBh Redirect Int 13h to Memory Technologies Devices such as ROM, RAM, PCMCIA, and serial disk.

CCh Redirect Int 10h to enable remote serial video

CDh Re-map I/O and memory for PCMCIA

CEh Initialize digitizer and display message.

D2h Unknown interrupt

The following are for boot block in Flash ROM

E0h Initialize the chipset

E1h Initialize the bridge

E2h Initialize the CPU

E3h Initialize the system timer

E4h Initialize system I/O

E5h Check force recovery boot

E6h Checksum BIOS ROM

E7h Go to BIOS

E8h Set Huge Segment

Code Beeps POST Routine Description

Chapter 4 85

E9h Initialize Multi Processor

EAh Initialize OEM special code

EBh Initialize PIC and DMA

ECh Initialize Memory type

EDh Initialize Memory size

EEh Shadow Boot Block

EFh System memory test

F0h Initialize interrupt vectors

F1h Initialize Run Time Clock

F2h Initialize video

F3h Initialize System Management Mode

F4h 1 Output one beep

F5h Clear Huge Segment

F6h Boot to Mini DOS

F7h Boot to Full DOS

Code Beeps POST Routine Description

86 Chapter 4

Index of Symptom-to-FRU Error Message

LCD-Related Symptoms

Symptom/Error Action in SequenceLCD backlight doesn't work.LCD is too dark.LCD brightness cannot be adjusted.LCD contrast cannot be adjusted.

Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system.Reconnect the LCD connectors.Keyboard (if contrast and brightness function key do not work).LCD inverter IDLCD cableLCD inverterLCDSystem board

Unreadable LCD screen Missing pels in charactersAbnormal screen Wrong color displayed

Reconnect the LCD connector.LCD inverter IDLCD cableLCD inverterLCDSystem board

LCD has extra horizontal or vertical lines displayed.

LCD inverter IDLCD inverterLCD cableLCDSystem board

Indicator-Related Symptoms

Symptom/Error Action in SequenceIndicator incorrectly remains off or on, but system runs correctly.

Reconnect the inverter boardInverter boardSystem board

Power-Related Symptoms

Symptom/Error Action in SequencePower shuts down during operation.

Power source (battery pack and power adapter). See “Power System Check”. Battery packPower adapterHard drive & battery connection boardSystem board

The system doesn’t power on.

Power source (battery pack and power adapter). See “Power System Check”. Battery packPower adapterHard drive & battery connection boardSystem board

Chapter 4 87

The system doesn’t power-off.

Power source (battery pack and power adapter). See Power System Check”. Hold and press the power switch for more than 4 seconds. System board

Battery can’t be charged. See “Check the Battery Pack”. Battery packSystem board

PCMCIA-Related Symptoms

Symptom/Error Action in SequenceSystem cannot detect the PC Card (PCMCIA).

PCMCIA slot assemblySystem board

PCMCIA slot pin is damaged.

PCMCIA slot assembly

Memory-Related Symptoms

Symptom / Error Action in SequenceMemory count (size) appears different from actual size.

Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system.DIMMSystem board

Speaker-Related Symptoms

Symptom/Error Action in SequenceIn Windows, multimedia programs, no sound comes from the computer.

Audio driverSpeakerSystem board

Internal speakers make noise or emit no sound.

SpeakerSystem board

Power Management-Related Symptoms

Symptom/Error Action in SequenceThe system will not enter hibernation.

Keyboard (if control is from the keyboard)Hard disk driveSystem board

The system does not enter hibernation mode and four short beeps every minute.

Press Fn + F4 and see if the computer enters hibernation mode.TouchpadKeyboardHard disk connection boardHard disk driveSystem board

Power-Related Symptoms

Symptom/Error Action in Sequence

88 Chapter 4

The system does not enter standby mode after closing the LCD.

LCD cover switchSystem board

The system does not resume from hibernation mode.

Hard disk connection boardHard disk driveSystem board

The system does not resume from standby mode after opening the LCD.

LCD cover switchSystem board

Battery fuel gauge in Windows does not go higher than 90%.

Remove battery pack and let it cool for two hours.Refresh battery (continue to use battery until power off, then charge battery).Battery packSystem board

System hangs intermittently.

Reconnect hard disk/CD-ROM drives. Hard disk connection boardSystem board

Peripheral-Related Symptoms

Symptom/Error Action in SequenceSystem configuration does not match the installed devices.

Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system.Reconnect hard disk/CD-ROM/diskette drives.

External display does not work correctly.

Press Fn + F5, LCD/CRT/Both display switchingSystem board

USB does not work correctly.

System board

Print problems Ensure the “Parallel Port” in the “Onboard Devices Configuration” of BIOS Setup Utility is set to Enabled.Onboard Devices ConfigurationRun printer self-test.Printer driverPrinter cablePrinterSystem Board

Serial or parallel port device problems.

Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup Utility is set to Enabled.Device driverDevice cableDeviceSystem board

Keyboard/Touchpad-Related Symptoms

Symptom/Error Action in SequenceKeyboard (one or more keys) does not work.

Reconnect the keyboard cable.KeyboardSystem board

Power Management-Related Symptoms

Symptom/Error Action in Sequence

Chapter 4 89

NOTE: If you can not correct the problems according to the anterior tables, see “Undetermined Problems”.

Touchpad does not work. Reconnect touchpad cable.Touchpad boardSystem board

Modem-Related Symptoms

Symptom/Error Action in SequenceInternal modem does not work correctly.

Modem phone portmodem combo boardSystem board

Keyboard/Touchpad-Related Symptoms

Symptom/Error Action in Sequence

90 Chapter 4

Intermittent ProblemsIntermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.

When analyzing an intermittent problems, follow the procedures below:

1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.

2. If no error is detected, do not replace any FRU.

3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Chapter 4 91

Undetermined ProblemsThe diagnostic problems does not identify which devices fail, which devices are incorrectly installed, whether a short circuit happens, or whether the system is inoperative.

NOTE: Verify if all devices attached are supported by the computer.

NOTE: Verify if the power supply used at the time of failure is operating correctly. You can refer to “Power System Check”.

Follow the procedures below to isolate the failing FRU. Do not isolate non-defective FRU.

1. Power off the computer.

2. Visually check the devices. If any problems are found, replace the FRU.

3. Remove or disconnect all of the following devices:

Non-Acer devices

Printer, mouse, and other external devices

Battery Pack

Hard disk drive

DIMM

CD-ROM / Diskette drive module

PC cards

4. Power on the computer.

5. Determine if the problem has been resolved.

6. If the problem does not recur, reconnect the removed devices one at a time until you find the failed FRU.

7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU.

System board

LCD assembly

92 Chapter 4

Jumper and Connector Location

Chapter 5

Top View

No. Description No. Description1 DC-in jack 2 USB connector

3 CRT connector 4 RJ11 & RJ45 connector

5 MDC module connector 6 MDC board connector

7 Main battery connector 8 ODD connector

9 Mini PCI slot 10 CPU

11 North bridge 12 DIMM slot

13 South bridge 14 HDD connector

Chapter 5 93

15 Line-in jack 16 Microphone-in jack

17 Line-out jack 18 Cardbus controller

19 USB connector 20 LAN controller

21 BIOS ROM 22 RTC battery connector

23 5-in-1 card reader

No. Description No. Description

94 Chapter 5

Bottom View

Item Description Item Description1 Keyboard controller 2 Keyboard connector

3 Lid switch connector 4 System fan connector

5 PCMCIA card reader 6 Function key board connector

7 Touch pad board connector 8 Speaker connector

9 Bluetooth module connector 10 LCD cable connector

Chapter 5 95

FRU (Field Replaceable Unit) List

Chapter 6

This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Aspire 9410 / 7110 and TravelMate 5610 / 5110. Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization).

Please note that when ordering FRU parts, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed service guide. For Acer authorized service providers, your Acer office may have a different part number code from those given in the FRU list of this printed service guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for service.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose them properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6 96

Exploded Diagram

97 Chapter 6

Parts

Aspire 9410 UMA

CATEGORY PART NAME DESCRIPTION ACER PART NO.

ADAPTERN/A ADAPTER 90W LITEON PA-

1900-04WR ADT 90W LITEON PA-1900-04WR

AP.09003.005

ADAPTER 90W DELTA ADP-90SB BBAAF

ADT 90W DELTA ADP-90SB BBAAF

AP.09001.004

BATTERYN/A RTC BATTERY BTY RTC MITSUBISHI

ROHS 23.TCBV1.003

BATTERY PACK LI+ 8CELL 2.4MAH SANYO

BTY PACK LI+ 8C 2.4AH SANYO

BT.00803.018

BATTERY PACK LI+ 8CELL 2.4MAH SONY

BTY PACK LI+ 8C 2.4AH SONY

BT.00807.010

BATTERY PACK LI+ 6CELL 2.0MAH SONY

BTY PACK LI+ 6C 2.0AH SONY

BT.00604.010

BATTERY PACK LI-MN 6CELL 2.0MAH SANYO

BTY PACK LI-MN 6C 2.0AH SANYO

BT.00603.021

BATTERY PACK LI-MN 6CELL 2.0MAH PANASONIC

BTY PACK LI-MN 6C 2.0AH PANA

BT.00605.005

BLUETOOTH MODULE FOXCONN BCM2045 V01

BT MODULE FOXCONN BCM2045 V01

54.TB2V1.001

BOARDTOUCHPAD BOARD SYNPATICT M61PUF1G372

TOUCHPAD SYNPATICTM61PUF1G372

56.A46V1.001

LED BOARD MYALL LED BOARD 05569-2 (DIP)

55.TCBV1.001

"INVERTER BOARD 17"" FOXCONN T62I240.00 ROHS"

INVERTER 17'' VK.21189.402

19.TCBV1.001

"INVERTER BOARD 17"" YEC YNV-W02"

"INVERTER 17"" YEC YNV-W02"

19.TB2V1.001

"INVERTER BOARD 17"" O2 V189-601"

"INVERTER 17"" O2 V189-601"

19.ADFV1.001

Chapter 6 98

WIRELESS LAN BOARD 802.11ABG INTEL 3945 RW

WLAN 802.11ABG INTEL 3945 RW

KI.GLN01.003

WIRELESS LAN BOARD 802.11ABG INTEL 3945 MW2

WLAN 802.11ABG INTEL 3945 MW2

KI.GLN01.002

WIRELESS LAN BOARD 802.11ABG INTEL 3945 MW1

WLAN 802.11ABG INTEL 3945 MW1

KI.GLN01.001

WIRELESS LAN BOARD 802.11BG FOXCONN BCM4318 MURA

WLAN 802.11BG FOX BCM4318 MURA

54.A74V1.002

MODEM BOARD FOXCONN T60M893.03

MODEM MDC1.5 FOXCONNT60M893.03

54.TCBV1.001

N/A TV TUNER BOARD TV TUNER MINIPCI M103 HYBRID

54.ADFV1.001

TV TUNER BOARD TV TUNER MINIPCI M104 H/W ENCO

54.ADFV1.002

CABLEN/A BLUETOOTH CABLE B/T CABLE HT MYALL 50.TCBV1.001

TOUCHPAD CABLE T/P FFC CABLE MYALL

50.TCBV1.002

LAUNCH BOARD CABLE LAUNCH BOARD FFC CABLE MYALL

50.TCBV1.003

N/A COVER SWITCH CABLE COVER SWITCH HT MYALL

50.TCBV1.004

N/A "LCD CABLE 17.1"" WXGA" "LCD CABLE 17.1"" WXGA HT MYALL "

50.TCBV1.005

N/A "LCD CABLE 17.1"" WXGA" "C.A. 17.1"" WXGA HT MYALL-2 "

50.ADFV1.001

N/A MODEM CABLE MDC CABLE HT MYALL

50.TCBV1.006

CATEGORY PART NAME DESCRIPTION ACER PART NO.

99 Chapter 6

N/A POWER CORD 10A 250V 3PIN ITALY

CORD 10A 250V 3P ITALY BK

27.01518.711?

POWER CORD 10A 250V 3PIN ITALY

CORD ITALY 10A 250V 3P BK

27.01518.611

POWER CORD 10A 250V SWISS

CODE 10A 250V 3P SWISS BK

27.01518.691

POWER CORD 10A 250V SWISS

CODE SWISS POWER 10A 250V BK

27.01518.581

POWER CORD 10A 250V 3PIN BK SOUTH AFRICA

CODE 16A 250V SOUTH AFRICA BK

27.01518.681

POWER CORD 10A 250V 3PIN BK SOUTH AFRICA

CODE SOUTH AFRICA 10A 250V BK

27.01518.571

POWER CORD 7A 250V 2PIN KOREAN

CODE 7A250V 2P 1830 KOREAN

27.01518.531

POWER CORD 7A 125V 2PIN JAPEN

CODE JAPAN 7A 125V 2P BK

27.01518.551

POWER CORD 2.5A 250V AUSTRALIA

CODE 2.5A 250V AUSTRALIA BK

27.01518.621

POWER CORD 10A 125V 3PIN US BK

CODE 10A 125V 3P US BK

27.01518.641

POWER CORD 10A 125V US CODE US 10A 125V BK

27.T30V1.001

POWER CORD 10A 250V 3PIN CHINA BK

CORD 10A 250V 3P CHINA BK

27.01518.701

POWER CORD 10A 250V 3PIN CHINA

CORD CHINA 10A 250V 3P

27.01518.591

POWER CORD 10A 250V SOUTH AFRICA BK

CORD 10A 250V SOUTH AFRICA BK

27.01518.721

POWER CORD 2.5A 250V SOUTH AFRICA BK

CORD 2.5A 250V SOUTH AFRICA BK

27.01518.631

POWER CABLE 16A 250V 3PIN EUR BK

CORD 16A 250V 3P EUR BK

27.01518.731

POWER CORD 220V 3PIN EUR

CORD EUR 220V 3P BK

27.T30V1.004

POWER CORD 2.5A 125V USA

CORD USA/W CNS 2.5A 125V 8121-

27.01518.781

POWER CORD 5A 250V 3PIN UK BK

CODE 5A 250V 3P UK BK

27.03118.001

POWER CORD 3A 250V 3PIN UK

CODE UK 3A 250V 3P BK

27.01518.541

POWER CORD ACA / ACNZ POWER CODE ACA / ACNZ ANNIE

27.03218.021

POWER CODE 7A 125V 2PIN JAPAN

CODE 7A 125V JAPAN 2PIN BK

27.03518.161

POWER CODE 10A 250V 3PIN DENMARK BK

CODE 10A 250V 3P DENMARK BK

27.01518.671

POWER CORD 10A 3PIN BK CODE DENMARK 10A 3P BK

27.01518.561

CASE / COVER / BRACKET ASSEMBLY

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 100

MIDDLE COVER ASSY MIDDLE COVER--AS MYALL

60.ACKV1.003

MINI PCI COVER ASSY MINIPCI COVER MYALL

42.TCBV1.003

N/A MINI CARD COVER ASSY MINICARD COVER MYALL

42.TCBV1.004

HDD COVER ASSY HDD COVER MYALL

42.ACKV1.001

DIMM COVER ASSY DIMM COVER MYALL

42.TCBV1.002

LED BOARD SUPPORT BRACKET

U-CASE SUP. BKT L MYALL

33.TCBV1.001

OPTICAL BRACKET ODD BRKT MYALL 33.TCBV1.002

UPPER CASE W/COVER SWITCH CABLE

ASSY U_CASE--AS SLIDE MYALL2

60.ADFV1.002

LOWER CASE W/SPEAKER ASSY L-CASE W/O CARD READER

60.ADFV1.001

COMBO BEZEL ASSY COMBO ODD BEZEL GB

42.TCBV1.011

CATEGORY PART NAME DESCRIPTION ACER PART NO.

101 Chapter 6

N/A DVD DUAL BEZEL ASSY DVD_DUAL ODD BEZEL

42.TCBV1.012

DVD SUPER MULIA BEZEL ASSY S_MULTI ODD BEZEL GBASE

42.TCBV1.013

DVD SUPER MULIA BEZEL ASSY ODD SLOT-IN BEZEL

42.TCBV1.014

HDD CHASSIS ASSY HDD CHASSIS MYALL

33.TCBV1.003

"LCD PANEL 17.1"" W/LOGO" "ASSY LCD 17.1"" PANEL-AS MYALL "

60.ACKV1.005

"LCD BEZEL 17.1"" W/LOGO" "ASSY LCD BEZEL 17.1"" MYALL "

60.TCBV1.004

HINGE PACK LEFT/RIGHT "HINGE PACK 17"" LEFT/RIGHT"

6K.TCBV1.001

LCD BARCKET LEFT "BRKT LCD 17.1"" L MYALL "

33.TCBV1.005

LCD BRACKET RIGHT "BRKT LCD 17.1"" R MYALL "

33.TCBV1.004

N/A CAMERA HOLDER HLDR CAMERA SIDE RIM KIRKINI

42.ADFV1.001

N/A CAMERA LOWER CASE CAS CAS CAMERA L-CASE KIRKINI

39.ADFV1.001

N/A CAMERA HOLDER CAP HLDR CAMERA CAP KIRKINI

42.ADFV1.002

N/A CAMERA LATCH LATCH CAMERA HINGH KIRKINI

33.ADFV1.003

N/A CAMERA LOWER CASE ASSY CAMERA LCASE KIRKINI

60.ADFV1.006

SPEAKERN/A SPEAKER LEFT/RIGHT SPEAKER MYALL 23.TCBV1.001

COMBO MODULE

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 102

COMBO MODULE 24X ASSY ODD COMBO MYALL2

6M.ADFV1.001

CDRW/DVD COMBO DRIVE 24X PHILIPS SCB5265 W/O BEZEL

COMBO PHI/SCB5265 MYALL NOBZL

KO.02408.010

CDRW/DVD COMBO DRIVE 24X LITEON SOSC-2485K W/O BEZEL

COMBO LIT/SOSC-2485K NO BZL

KO.02409.022

DVD-RW DRIVEN/A DVD-RW DRIVE 8X DUAL ASSY ODD DUAL

MYALL26M.ADFV1.002

DVD-RW DRIVE 8X DUAL TS-L532U W/O BEZEL

DUAL TOS/TS-L532U W/BOLSENA BZ

KU.00801.005

DVD-RW DRIVE 8X DUAL PHILIPS SDVD8441 W/O BEZEL

DUAL PHI/SDVD8441 NO BZL MORAR

KU.00809.002

DVD-RW DRIVE 8X SUPER MULTI SLOT IN

ASSY ODD S-MULTI MYALL2

6M.ADFV1.003

DVD-RW DRIVE 8X SUPER MULTI SLOT IN TOSHIBA TS-L632D W/O BEZEL

S-MULT 8X TST/TS-L632D W/O BZL

KU.00801.014

DVD-RW DRIVE 8X SUPER MULTI SLOT IN LITEON SSM-8515S W/O BEZEL

S-MULTI LTN/SSM-8515S BOLSEN-E

KU.00804.022

DVD-RW DRIVE 8X SUPER MULTI SLOT IN PHI SDVD-8821 W/O BEZEL

SUP-MULT PHI/SDVD-8821 KERKINI

KU.00809.005

DVD-RW DRIVE 8X SUPER MULTI SLOT IN LITEON SSM-8515S W/O BEZEL

S-MULTI LTN/SSM-8515S MYALL/2

KU.00804.037

DVD-RW DRIVE 8X SUPER MULTI SLOT IN

ASSY ODD SLOT-IN PIONEER

6M.ADFV1.004

DVD-RW DRIVE 8X SUPER MULTI SLOT IN PIONEER DVR-K06RS W/O BEZEL

SUP-MULT PIO/DVR-K06RS SLOT LF

KU.00805.027

DVD-RW DRIVE 8X SUPER MULTI SLOT IN

ASSY ODD SLOT-IN PANASONIC

6M.ADFV1.005

DVD-RW DRIVE 8X SUPER MULTI SLOT IN PANASONIC UJ-855 W/O BEZEL

SUP-MULT PAN/UJ-845 SLOT LF AG

KU.00807.029

CPU

CATEGORY PART NAME DESCRIPTION ACER PART NO.

103 Chapter 6

CPU DC YONAH T2300 1.66GMHZ INTEL

IC CPU DC YONAH T2300 1.66G PGA

KC.23001.DTP

CPU DC YONAH T2600 2.17GMHZ INTEL

IC CPU DC YONAH T2600 2.17G PGA

KC.26001.DTP

CPU DC YONAH T2500 2GMHZ INTEL

IC CPU DC YONAH T2500 2G PGA

KC.25001.DTP

CPU DC YONAH T2400 1.83GMHZ INTEL

IC CPU DC YONAH T2400 1.83G PGA

KC.24001.DTP

CPU DC YONAH T2300 1.66GMHZ INTEL

IC CPU DC YONAH T2300 1.66 PGA

KC.23E01.DTP

CPU YONAH CEL-M 430 1.73GNHZ INTEL

IC CPU YONAH CEL-M 430 1.73 PGA

KC.N0001.430

CPU YONAH CEL-M 420 1.6GMHZ INTEL

IC CPU YONAH CEL-M 420 1.6 PGA

KC.N0001.420

FANFAN FAN SUNON MYALL 23.TCBV1.004

FAN FAN FORCECON MYALL

23.TCBV1.004

FAN FAN KME MYALL 23.TCBV1.004

HDD

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 104

N/A HDD 60G 4200RPM SEAGATE ST960812A

HDD 60GB SEAGATE ST960812A

KH.06001.006

HDD 60G HITACHI HTS421260H9AT00

HDD 60GB HGST HTS421260H9AT00

KH.06007.009

HDD 60G 4200RPM TOSHIBA MK6025GAS

HDD 60GB TOSHIBA MK6025GAS

KH.06004.004

HDD 60G 5400RPM SEAGATE ST96812A

HDD 60GB SEAGATE ST96812A

KH.06001.007

HDD 60G 5400RPM TOSHIBA

HDD 60GB TOSHIBA 5400RPM

KH.06004.007

HDD 60G 5400RPM HITACHI HTS541260H9AT00

HDD 60GB HGST HTS541260H9AT00

KH.06007.011

HDD 80G 4200RPM SEAGATE ST980829A

HDD 80GB SEAGATE ST980829A

KH.08001.021

HDD 80G 4200RPM HITACHI HTS421280H9AT00

HDD 80GB HGST HTS421280H9AT00

KH.08007.011

HDD 80G 4200RPM TOSHIBA MK8025GAS

HDD 80GB TOSHIBA MK8025GAS

KH.08004.003

HDD 80G 5400RPM SEAGATE ST98823A

HDD 80GB SEAGATE ST98823A

KH.08001.022

HDD 80G 5400RPM WD WD800UE-22HCT0

HDD 80GB WD WD800UE-22HCT0

KH.08008.027

HDD 80G 5400RPM TOSHIBA

HDD 80GB TOSHIBA 5400RPM

KH.08004.006

HDD 80G 5400RPM HITACHI "HDD 80G 2.5"" 5400RPM HGST"

KH.08007.013

HDD 100G 4200RPM SEAGATE ST9100825A

HDD 100GB SEAGATE ST9100825A

KH.10001.006

HDD 100G HITACHI HTS421210H9AT00

HDD 100GB HGST HTS421210H9AT00

KH.10007.002

HDD 100G TOSHIBA MK1031GAS

HDD 100GB TOSHIBA MK1031GAS

KH.10004.001

HDD 100G 5400RPM HITACHI 13G1591 ROHS

HDD 100GB HGST 13G1591 ROHS

KH.10007.004

HDD 100G 5400RPM SEAGATE ST9100824A

HDD 100GB SEAGATE ST9100824A

KH.10001.007

HDD 100G 5400RPM TOSHIBA MK1032GAX

HDD 100GB TOSHIBA MK1032GAX

KH.10004.002

HDD 100G 5400RPM SAMSUNG HM100JC

HDD 100GB SAMSUNG HM100JC

KH.1000B.002

HDD 120G HITACHI HTS421212H9AT00

HDD 120GB HGST HTS421212H9AT00

KH.12007.008

HDD 120G 4300RPM SEAGATE ST9120824A

HDD 120GB SEAGATE ST9120824A

KH.12001.023

HDD 120G 4200RPM SEAGATE MK1233GAS

HDD 120G MK1233GAS 4200RPM ROH

KH.12004.001

CATEGORY PART NAME DESCRIPTION ACER PART NO.

105 Chapter 6

N/A HDD 120G 4200RPM HITACHI 0A26308

HDD 120GB HGST 0A26308 ROHS

KH.12007.006

HDD 120G 5400RPM SEAGATE ST9120821A

HDD 120GB SEAGATE ST9120821A

KH.12001.024

HDD 120G 5400RPM TOSHIBA

HDD 120GB TOSHIBA 5400RPM

KH.12004.002

HDD 160G 5400RPM SEAGATE ST9160821A

HDD 160GB SEAGATE ST9160821A

KH.12001.024

HEATSINKCPU HEATSINK ASSY CPU HSINK CCI

UMA MYALL 34.TBHV1.001

KEYBOARDAS9400/7100 KEYBOARD DARFON US INTERNATIONAL

AS9400/7100 KEYBOARD DARFON US INTERNATIONAL

KB.ACF07.001

AS9400/7100 KEYBOARD DARFON CHINESE

AS9400/7100 KEYBOARD DARFON CHINESE

KB.ACF07.002

AS9400/7100 KEYBOARD DARFON SPANISH

AS9400/7100 KEYBOARD DARFON SPANISH

KB.ACF07.003

AS9400/7100 KEYBOARD DARFON THAI

AS9400/7100 KEYBOARD DARFON THAI

KB.ACF07.004

AS9400/7100 KEYBOARD DARFON BRAZILIAN PROTUGESE

AS9400/7100 KEYBOARD DARFON BRAZILIAN PROTUGESE

KB.ACF07.005

AS9400/7100 KEYBOARD DARFON KOREA

AS9400/7100 KEYBOARD DARFON KOREA

KB.ACF07.006

AS9400/7100 KEYBOARD DARFON UK

AS9400/7100 KEYBOARD DARFON UK

KB.ACF07.007

AS9400/7100 KEYBOARD DARFON GERMAN

AS9400/7100 KEYBOARD DARFON GERMAN

KB.ACF07.008

AS9400/7100 KEYBOARD DARFON ITALIAN

AS9400/7100 KEYBOARD DARFON ITALIAN

KB.ACF07.009

AS9400/7100 KEYBOARD DARFON FRENCH

AS9400/7100 KEYBOARD DARFON FRENCH

KB.ACF07.010

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 106

AS9400/7100 KEYBOARD DARFON SWISS/G

AS9400/7100 KEYBOARD DARFON SWISS/G

KB.ACF07.011

AS9400/7100 KEYBOARD DARFON PORTUGUESE

AS9400/7100 KEYBOARD DARFON PORTUGUESE

KB.ACF07.012

AS9400/7100 KEYBOARD DARFON ARABIC

AS9400/7100 KEYBOARD DARFON ARABIC

KB.ACF07.013

AS9400/7100 KEYBOARD DARFON BELGIUM

AS9400/7100 KEYBOARD DARFON BELGIUM

KB.ACF07.014

AS9400/7100 KEYBOARD DARFON SWEDEN

AS9400/7100 KEYBOARD DARFON SWEDEN

KB.ACF07.015

AS9400/7100 KEYBOARD DARFON CZECH

AS9400/7100 KEYBOARD DARFON CZECH

KB.ACF07.016

AS9400/7100 KEYBOARD DARFON HUNGAIAN

AS9400/7100 KEYBOARD DARFON HUNGAIAN

KB.ACF07.017

AS9400/7100 KEYBOARD DARFON NORWAY

AS9400/7100 KEYBOARD DARFON NORWAY

KB.ACF07.018

AS9400/7100 KEYBOARD DARFON DANISH

AS9400/7100 KEYBOARD DARFON DANISH

KB.ACF07.019

AS9400/7100 KEYBOARD DARFON TURKISH

AS9400/7100 KEYBOARD DARFON TURKISH

KB.ACF07.020

AS9400/7100 KEYBOARD DARFON CANADIAN FRENCH

AS9400/7100 KEYBOARD DARFON CANADIAN FRENCH

KB.ACF07.022

AS9400/7100 KEYBOARD DARFON GREEK

AS9400/7100 KEYBOARD DARFON GREEK

KB.ACF07.024

AS9400/7100 KEYBOARD DARFON HEBREW

AS9400/7100 KEYBOARD DARFON HEBREW

KB.ACF07.025

AS9400/7100 KEYBOARD DARFON RUSSIAN

AS9400/7100 KEYBOARD DARFON RUSSIAN

KB.ACF07.026

AS9400/7100 KEYBOARD DARFON SLOVENIA (SLO)

AS9400/7100 KEYBOARD DARFON SLOVENIA (SLO)

KB.ACF07.027

COMMUNICATION MODULEN/A WIRELESS ANTENNA ANTENNA CABLE

MYALL2 25.ADFV1.001

LCDN/A "ASSY LCD MODULE 17""

WXGA GLARE""ASSY 17"" LCD GLARE AS "

6M.ADFV1.011

CATEGORY PART NAME DESCRIPTION ACER PART NO.

107 Chapter 6

N/A "LCD 17"" WXGA+ LG LP171WP4-TL02 GLARE"

"LCD 17""W LP171WP4-TL02 GLARE"

LK.17008.015

N/A "LCD 17.1"" WXGA+ QDI QD17TL02-05 NONE GLARE "

"LCD 17""W QDI QD17TL02-05"

LK.17109.001

N/A "LCD 17""WXGA+ QDI QD17TL02-06 GLARE"

"LCD 17"" QD17TL02-06 GLARE"

LK.17109.002

N/A "LCD 17.1"" WXGA+ SAMSUNG LTN170WX-L05 NONE GLARE "

"LCD 17""W LTN170WX-L05 "

LK.17106.001

N/A "LCD 17"" WXGA+ SAMSUNG LTN170WX-L05-H GLARE"

"LCD 17""W LTN170WX-L05-H GLARE"

LK.17106.002

N/A "LCD 17"" WXGA+ AU B170PW03 V4 GLARE "

"LCD 17""WXGA B170PW03 V4 GLARE "

LK.17105.005

N/A "LCD 17.1"" WXGA+ AU B170PW03 V3 NONE GLARE "

"LCD 17""W AU B170PW03 V3"

LK.17105.006

N/A "ASSY LCD MODULE 17"" WXGA GLARE CCD 1.3M"

"ASSY 17"" LCD GLARE CCD AS "

6M.ADFV1.012

N/A ASSY LCD MODULE 17" WXGA GLARE CCD 300K

ASSY 17" 300K CCD GLARE AS

6M.ADFV1.013

CAMERAN/A CAMERA CMOS 1.3M

LOGITECH 961458-2000 L CAMERA CMOS 1.3M 961458-2000 L

56.ABAV1.001

N/A CAMERA CMOS 300K VFA BN2QA350K8SD79

CAMERA CMOS VFA BN2QA350K8SD79

56.ADFV1.001

MAINBOARDMAINBOARD MYALL 2 W/MODEM & MODEM CABLE & RTC BATTERY W/O CPU & MEMORY (Aspire 9410 UMA, TravleMate 5610 UMA)

MYALL2 MB 06203-1 945GM (D) (Aspire 9410 UMA, TravelMate 5610 UMA)

MB.TCS01.001

MAINBOARD MYALL 2 W/MODEM & MODEM CABLE & RTC BATTERY W/O CPU & MEMORY (Aspire 9410 DISCRETE)

MYALL2 MB 06203-1 64MB VRAM (D) (Aspire 9410 DISCRETE)

MB.TCT01.001

MAINBOARD MYALL 2 W/MODEM & MODEM CABLE & RTC BATTERY W/O CPU & MEMORY (Aspire 9410 DISCRETE, TravelMate 5610 DISCRETE)

MYALL2 MB 06203-1 128MB VRAM (D) ( Aspire 9410 DISCRETE, TravelMate 5610 DISCRETE)

MB.TCU01.001

MAINBOARD MYALL 2 W/MODEM & MODEM CABLE & RTC BATTERY W/O CPU & MEMORY (Aspire 7110 UMA)

MYALL2 MB 06203-1 940GML (D) (Aspire 7110 UMA)

MB.TCW01.001

SLOT

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 108

N/A PCMCIA SLOT 4PIN CONN CARDBUS 4P 59330-00L0C

22.T28V1.001

MEMORYSDIMM 256M SAMSUNG 470T3354CZ3-CD5

SODIMM 256M M470T3354CZ3-CD5

KN.2560B.017

SDIMM 256M MICRON MT4HTF3264HY-53EB4

SODIMM 256M MT4HTF3264HY-53EB4

KN.25604.030

SDIMM 256M HYNIX HYMP532S64BP6-C4

SODIMM 256M HYMP532S64BP6-C4

KN.2560G.012

DIMM 256M NANYA NT256T64UH4A1FN-37B

DIMM 256M NT256T64UH4A1FN-37B

KN.25603.029

SDIMM 256M INFINEON HYS64T32000HDL-3.7-A

SODIMM256MHYS64T32000HDL-3.7-A

KN.25602.023

SDIMM 512M NANYA NT512T64UH8A1FN-37B

SODIMM512M NT512T64UH8A1FN-37B

KN.51203.023

SDIMM 512M SAMSUNG M470T6554CZ3-CD5

SODIMM 512M M470T6554CZ3-CD5

KN.5120B.015

SDIMM 512M INFINEON MHYS64T64020HDL-3.7-A

SODIMM512MHYS64T64020HDL-3.7-A

KN.51202.021

SDIMM 512M ELPIDA GU33512AGEPN612C

SODIMM 512M GU33512AGEPN612C

KN.51209.005

SDIMM 512M HYNIX HYMP564S64BP6-C4

SODIMM 512M HYMP564S64BP6-C4

KN.5120G.013

SDIMM 1G HYS64T128021HDL-3.7-A

SODIMM1G HYS64T128021HDL-3.7-A

KN.1GB02.023

SDIMM 1GB 533 NANYA SO-DIMM DDRII 533 1GB NANYA

KN.1GB03.006

SDIMM 1G GU331G0AGEPN6E2C

SODIMM 1G GU331G0AGEPN6E2C

KN.1GB09.004

MICROPHONEMICROPHONE MICROPHONE MICROPHONE

SUNMOWNG MYALL 23.TCBV1.002

MISCELLANEOUSMISCELLANEOUS LCD SCREW RUBBER RUB LCD RUBBER

CUSHION BOLSENA 47.A46V1.002

MISCELLANEOUS LCD SCREW RUBBER RUBBER SCREW MYALL

47.TCBV1.001

MISCELLANEOUS LOGO PLATE FOR PANEL PLT LOGO PANEL 31.T49V1.001

MISCELLANEOUS LOGO PLATE FOR BEZEL "PLT BEZEL PLATE ""ACER "" LOGO "

31.A46V1.001

SCREWN/A SCREW SCW HEX NYL I#R-

40/O#4-40 L5.5 34.00015.081

CATEGORY PART NAME DESCRIPTION ACER PART NO.

109 Chapter 6

N/A SCREW SCREW MACH WAFER M2*L4 NI

86.T39V1.002

N/A SCREW SCRW M2.5*6 ~ L-CASE + U-CASE

86.00D28.330

N/A SCREW SCRW M2*L3 86.00D29.620

N/A SCREW SCRW M2.5*5 WAFER B-ZN ROHS

86.00D47.630

N/A SCREW SCREW M2*L3 NYLOK CR 3+

86.00E25.723

N/A SCREW SCREW M2*L3 NON-NYLOK CR3+

86.00E31.723

N/A SCREW SCREW M2.5*L6 NYLOK CR3+

86.00E33.736

N/A SCREW SCREW M2.5*L8 NYLOK CR3+

86.00E34.738

N/A SCREW SCREW M2*L8 NI NON-NYLOK

86.00E35.228

N/A SCREW SCREW M3x4(86.9A524.4R0)

86.9A524.4R0

N/A SCREW SCRW M2*4 WAFER NI

86.9A552.4R0

N/A SCREW SCREW NI M2*6L 86.9A552.6R0

N/A SCREW SCRW M2.5*L3(NON NYLOK)

86.9A523.3R0

CATEGORY PART NAME DESCRIPTION ACER PART NO.

Chapter 6 110

Aspire 9410 / 7110 TravelMate 5610 / 5110 Service Guide · Aspire 9410 / 7110 TravelMate 5610 / 5110 Service Guide ... (Aspire 9410 / 7110 series) T Acer ClearVisionTM ... 7 N/A Touchpad - [PDF Document] (2024)

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Virgilio Hermann JD

Last Updated:

Views: 5699

Rating: 4 / 5 (61 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Virgilio Hermann JD

Birthday: 1997-12-21

Address: 6946 Schoen Cove, Sipesshire, MO 55944

Phone: +3763365785260

Job: Accounting Engineer

Hobby: Web surfing, Rafting, Dowsing, Stand-up comedy, Ghost hunting, Swimming, Amateur radio

Introduction: My name is Virgilio Hermann JD, I am a fine, gifted, beautiful, encouraging, kind, talented, zealous person who loves writing and wants to share my knowledge and understanding with you.